Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

oleskool

1996 Yamaha 350 4x4 No Start

Recommended Posts

Has new top end, piston, rings, valves, etc. great compression, good spark, plenty of fuel. Valves have been set. timing has been tripled checked. Can not get it to start. any ideas suggestions on anything I am missing. Also if anyone has the service manual it would be greatly appreciated.

Thanks

Edited by oleskool
  • Like 1

Share this post


Link to post
Share on other sites


Are you getting fuel to the plug? If so, have you checked for fuel in the oil. I have seen fresh rebuilds have fuel wash down the cylinder walls and keep you from starting the bike. I have even had it happen to an old Dodge truck. The more you try to start it, the more fuel you get in the crank case.

Share this post


Link to post
Share on other sites

Did you find a solution to your issue? I have had similar problems with my big bear 95.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Daniel Gibson
      Working on a bayou 220 that has been ran extremely hard it's whole life. Literally had almost an inch thick dirt/oil covering the motor. Yeah that bad. Surprisingly it runs though. I cleaned the carb and tank multiple times. They're clean enough to eat off of. Readjusted valve lash and set timing. Was about 3 teeth off. It cranks good and runs good only problem is I have to cover the carb intake basically choking the hell out of it for it to start. The com choke works fine. It does this each time I start it regardless of temperature both ambient or motor. Wth? Compression is at 115psi I get 130s if I put a little oil in the piston chamber. Please help. Thanks 
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By Dwight Williams
      Hey everyone, I've been scratching my head over this for most of the day.  I bought a couple of Bayou 220's, got them running (they've both been sitting), and started tweaking and fixing small things.  One of them is mostly done, the other had an aftermarket carb on it and I've been trying to sort that out.
       
      Anyway, while adjusting the carb it died a few times, I restarted and moved on until it died and wouldn't restart.  I figured maybe I'd flooded it or something - after further attempts I realized I had no spark.  Since I have two identical machines I have many parts at my disposal.  I've swapped the CDI, spark plug and coil with no luck.  I have good resistance readings from the stator and pick up (135 and 110 respectively),  I don't have a peak voltage meter but I measure around 53VAC on the stator when cranking.  I have a 4 wire stator, not an alternator like the newer ones.  Grounds look good, I've checked the kill switch by verifying that it and the ignition switch grounds the black/yellow wire to the CDI.  I can turn the engine slowly and see the pickup short the meter as well, seems normal right?  So far everything I've checked looks the same on both machines.  I've got the service manual and wiring diagrams.  Do these readings make any sense?  I'm obviously missing something but I'm stumped.  thanks!
    • By Dwight Williams
      Ok, so I bought a 2006 bayou 250 for 200 bucks, kid couldn't start it and had no idea why it wouldn't run, I pulled the rope and felt what I thought was valve to piston contact, he wanted 500 and I talked him down to 200 and brought it home.  Sure enough, timing was way far out, timing chain incredibly loose.  So for fun I re-tensioned the timing chain and re timed it, got about 120lbs of compression, pretty low.  I cannot get the chain very tight but the the tensioner seems to work fine, the chain guides don't look very worn.  Also, when I took the head off the valves don't look bent and the piston has no discernible marks on it.  Is this an interference engine?  I sure thought I felt some contact with the pull rope but maybe no permanent damage was done?  Anyway, I plan on doing a full top end job as well as timing chain tensioners and hopefully that'll cure it.  Is there any reason other than chain stretch (I measured it and it's ok) or guide wear that would cause the chain to be so loose?  Thanks!
       
    • By technofarmer
      Hi there i was needing to ask a question. I may soon be getting a UTV of one sort or another and not sure what is good or better to avoid?  So far i hear great things about the Arctic Cat Prowler and Havoc, and many speak well of the Kawasaki Mule all but the 610?  
       
       So what are your thoughts and especially experiences?  What have you had and used in farm life and trail riding that has held up well or hasn't?        
  • Similar Tagged Content

    • By YamahaBB350
      I have a Yamaha Big Bear 350 and the reverse doesn’t work, it shifts from low to high easily but it won’t go back to reverse. I’m new to this stuff, so I’ll take any help. Any ideas? 
    • By Colin James Krepela
      So here's the deal people, I have an old Avenger 350 4X4 Shaft Driven ATV. They only made them in the early 80's their thought of as the first four wheelers from around back when Suzuki made one in 1982. I believe the engine on it is a Kohler as I watched this video https://www.bing.com/videos/search?q=avenger+400+atv&view=detail&mid=1E10E939019CA07770031E10E939019CA0777003&FORM=VIRE but mine is a 350. That's if its original, and it all looks original. I am wondering where I can get parts for this engine, or really what engine is it. I have no way to find the year, unless you guys know where a serial number might be. Every sticker is worn off. IF anyone has any information at all on these old wheelers it would be greatly appreciated. I specifically need the gaskets for the carb, and don't tell me I could build them please I want to restore it as perfectly as I can. I can take pictures of the wheeler/carb if it'll help. Let me know.
    • By Martin Carrière
      Recently bought my BB. Everything works great. Only thing is, each time I put it in reverse, it either starts to rev high and start moving without giving it gas or I'll give it a bit of gas and let go and it will still rev at the same rpm or higher and keep moving. Doesn't do it for high or low.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...