Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
Im new to the forum and the quad I just got. I want to change oil in in. Its almost impossible to find anything on-line. I know it takes 10w40 and know the oil filter location. What oil should I use? Is there a cross reference for oil filter. The closest dealer to me is an hour away. I have NAPA close and like the WIX or Napa gold filters. Also is where can I get a Manuel for it? Thanks
Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires.... Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
Thank you in advance for sharing your knowledge.
Can anyone point me to a good set of instructions for changing front diff oil on a 1987 Suzuki LT4WD? I can almost guess which bolts are drain & fill... but I've been wrong before... 😆
I found some partial posts on other forums and they linked out to dead images and whatnot. Any help appreciated.
This thing is running pretty good, got the front brakes back to life, electric start works fine, seat cover fixed up, plastics stitched back together...
BEFORE (last week):
Hi bought this quad with a few leaks and other issues which thanks to excellent advice from these forums I thought I’d sorted them till I washed it down and found oil underneath.
It is coming from the seal around the gear changer pedal as it looks like someone has banged the housing flat on one side. Knowing how easily aluminium is broken I don’t wanna risk tapping it back into shape. Would a new seal fit or would the distortion of the housing render it useless.
thanks in advance
Similar Tagged Content
Looking to get some tires for my old quad, but the tires are getting rarer. Paying near 100 for tires seems a lot when that is what I just paid for tires for my car and i only ride four or five times a year
Anyone have any leads on good used or closeouts in 23x10/12 and 23x8/12?
Additionally, what other sizes can I run that might be easier to find and not muck with the 4x4?
By Alan Callison
OK ya'll.I need your help again.My ATV, 2004 Yam Kodiak 400 4x4,needs a new REAR rim or wheel what have you,whatever term you prefer. I've posted pics here as you can see.The tire is a 25x10.00x12 . As you can see its a deep REAR rim.I cannot seem to find a deep REAR rim. (Capitalization for emphasis) . The only sizes I can find listed are for both the front and rear wheels which is 12x7 4/110. This doesn't help me much. So,who can help me out? Im getting desperate now!LOL!
My village has now made golf carts and atv's legal on the street and now that the wife and i can go cruise around i'm considering putting on street tires to save my knobbies. Thinking on the route of saving costs and using car rims i'm sure i will have to get adapters but has anyone had experiences doing this? Down falls? We dont mud or anything and they would be used for summer only.
I just purchased a set (4) of these for $349.00 on Amazon. They are going on my Cforce 400.
The guys on the CFMoto forum suggest I tune my clutch to make up for the increased weight, Tire Lug depth, etc.
I've been doing a ton of searching on CVTech clutches and I think I've found how to do it.
I've been told to add about 10g weight to my primary clutch and change the secondary to A1. If I don't do the weights I should atleast change the secondary to C1.
Does anyone here have experience with CVTech clutches and have any recommendations for me?
Anyone used SunF tires? 25-8-12/25-10-12
Sent from my iPhone using Tapatalk
Recently Browsing 0 members
No registered users viewing this page.