Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

LMI

2005 Suzuki King Quad 700 - Fan Replacement

Recommended Posts

The saga of the fan continues.

The Pin attempt in the fan shaft failed.  I then moved on to trying to weld the fan hub to the fan shaft.  I took it for a run the weld broke.  Now it was truly F'ed.  To recap the dealer price, they want $400 + CND for a replacement fan assembly.

I searched all sorts of after market places and no one carried one.  Ebay had some used ones but they were $120 USD + Conversion rate for something as old as what I have.  I went to Amazon and eventually settled on this.

 

amazon link

 

What I found... and was amazed... was that the fan mounted to the Suzuki fan assembly bracket.  I was prepared to manufacture my own mount conversions...  It also came with "Harpoon mounts" (nylon zip tie like things that go straight through the rad.   Anyways it mounted to the original bracket. It fit perfectly.  Cut the electrical plug off replaced it with the Suzuki... all good.  Let the quad heat up, thermo coupler kicked in the fan circuit, polarity was right... all was good....  Fan is under the circuit fuse rating.  

 

so I finally have a solid fan solution.  $34 CND vs $400+ CND

  • Like 1

Share this post


Link to post
Share on other sites


Speaking of fans, I just bought a 2005 king quad with some commander tracks in it. Can seems to be on most of the time. Is this normal or is she working harder with the tracks on it?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ed Zeppeli
      I have some wobble in my right rear wheel. Too much wobble.
       
      So I've torn into it and will need two bearings and two (different) seals. I'd like to get them locally if possible but need to know the number on the sides of the bearings and seals as I don't know that my bearing shop can source them by vehicle model. I'm told they're very common bearings.
       
      Any idea what the numbers are if mine end up being illegible?
       
      Thanks,
       
      Warren
    • By Tim-ANC
      Out riding last week. My son was riding my friend's Rincon. He was falling behind. I looked back at him and the left front tire was sideways. I thought, damn, I know what that is.
       
      The inner rod end ball had busted out of the socket housing. I was able to pop it back in then tied it up with pull start rope.
       
      Worked well enough to limp it back at slow speed.
    • By Jcolgin
      I have a 1998 Big bear 350...the tail pipe/spark arrestor is broke in the exhaust....how can I get it out to replace it? And what's the best way to get the new one in?
    • By ronwv48
      Just got a 2001 300 2x4 Bayou that needs a shifter shaft. Is this a very hard replacement to do? What do I need to watch for? Is there a video on this repair?
    • By Thunt56
      How do I replace the pinion clutch shaft in a 1987 Suzuki LT230 quadrunner? It starts up on the first kick but when I put it in gear it wants to kick up. I can give it gas and put it in gear but my clutch lever isn’t doing anything. SOS
  • Similar Tagged Content

    • By LMI
      I wanted to share an experience and a fix.
      Headed out was following a pole line, was looking for a cross track that may take me to this speckle trout looking spot on a creek.  All paths and semi paths... failed.  Second objective was to reach a speckle trout lake that has been recently stocked... followed 1 trail to dead end, followed second trail to dead end.... while investigating options on foot and the quad idling it died.
       
      It wouldn't start.  eventually it did... and when it did … it was essentially a pinned idle.  activating the throttle did seem to speed it up but it wouldn't knock out of the racing idle.  couldn't put it in gear at that idle speed.  got towed out.
      when I first got the quad, I ran it off a trail and buried it pretty good in the soft snow... eventually winched out.  It wouldn't start.  eventually did and it was fast idling.  not as fast as this last time. but still fast.  it eventually seemed to settle and I got it in gear and by the time I was back to the truck was acting ok.  chalked it up to the bike being at a bad angle in the snow.
      My investigation last year lead to the throttle position sensor TPS.  how to jumper the diag block to see the sensor position on the display,.  I focused on this nearly sure it was a detuned sensor or broken sensor again this time.
       
      I tore down the front plastic and stuck my head into the TPS area to see what I could see.  What I found was that the throttle body assembly had actually come out of the mounting area (not sure what it is called).  the ring clamp was loose I could move it easily.  Hopeful, I tore down the air intake assembly above it (air filter...etc) removed a sensor clip and a hose.
      I backed off the clamp some more and was able to reseat the throttle body assembly.  put some blue lock tite on the clamp screw.  When I was cleaning off the air intake assembly to ensure I dropped nothing down the intake, I noticed the underside of the air intake "box" also had a clamp.  this screw was completely missing.
      I went to the hardware store, bought a metric replacement (brought clamp with me), seated the assembly, settled the clamp blue lock tite that as well... 
       
      quad fired right up, idled normal, idled up without hesitation and dropped right back off.  Cost of solution $3.87 CND for a pack of 5 metric screws.  moral of my story was don't assume an idle issue is a throttle position sensor problem... there are a number of other factors including air pressure, which I believe was my issue.
       
       
       
    • By Andrew Serrano
      I have a 2000 Suzuki LTF -300 King Quad. My problem is it will start up great, very fast. It will run fine until it gets hot and I turn it off.  If I let it sit for a bit it will not start until I hold the throttle wide open and crank on the starter for quite some timr, acting has if flooded.....but I checked the spark plug one time this happened, went to change thinking it was flooded but only found a dry Plug????  It starts like if flooded but plug was dry, it takes awhile to start, then to get going I have to really rev it to get it clear and going...Thanks any suggestions would be great, thanks everybody in advance...!!!
    • By mikeexplorer
      Wiring diagram for 2007 Arctic Cat 700 EFI 4x4
       
       
    • By Admin
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
    • By Admin
      View File 2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      Submitter Admin Submitted 06/29/2019 Category Arctic Cat ATV  
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...