Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

maddog865

2013 Linhai Bighorn 400 valve specs needed

Recommended Posts



You can try these Linhai ATV Service manuals:

* Topic moved to Other brands atv forum and adjusted topic title for more info

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • Polaris ATV Valve Adjustment

      I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought. My bike is a 2005 Sp 500 HO. I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at. Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts) [ATTACH]1021[/ATTACH] then the side cam cover (5-8mm bolts). [ATTACH]1023[/ATTACH] Also remove the plug in the recoil cover (14mm bolt) to see the timming marks. [ATTACH]1022[/ATTACH] Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke. The best was to tell that your at TDC of the compression stroke is to rotate the engine until the timing marks are parallel to rocker cover gasket surface. The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line. Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on the flywheel into the center of the hole. [ATTACH]1023[/ATTACH] Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly [ATTACH]1024[/ATTACH] [ATTACH]1025[/ATTACH] To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs. The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple. I'd give it a 4 out of 10 on the skill level scale. I hope this helps! Thanks Rich

      By PolarisRich, in Polaris ATV Forum

        
      • 7 replies
      • 23,716 views
    • 2008 Linhai Quadzilla 300 E Need Service Manual

      hi just purchased linhai quadzilla 300 e  2008 am looking for service /repair manual  

      By Gary Patch, in Other ATV Brands Forum

        
      • 3 replies
      • 150 views
    • 2009 Linhai ATV Service Manual Multiple Models

      View File 2009 Linhai ATV Service Manual Multiple Models 2009 Linhai ATV Service Manual Multiple Models   ATV 260/300 Special Edition - Anniversary 2x4 4x4 Mini 50/80/100/150 B-Type 150/200, 2x4 260/300, 2x4/ 4x4 ATV520 ATV400-2 ATV400-2B Attachment: Delphi Small Engine Management System Service
      Manual  Submitter Ajmboy Submitted 11/02/2018 Category Other ATV  

      By Ajmboy, in Other ATV Brands Forum

        
      • 0 replies
      • 84 views
    • 1985 Suzuki LT250EF Quadrunner Valve & Rocker Arm Clearance

      I have a 1985 Suzuki lt250ef quadrunner and does anyone know the proper valve to rocker arms clearance 

      By Pvm85, in Suzuki ATV Forum

      • 3 replies
      • 1,097 views
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×