-
Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
Rear axle bearing replacement on an 04 Yam Kodiak 400 4x4
-
Similar Forum Topics
-
By flyinbrian365
View File 2010 Polaris Sportsman 850 All Models Service Manual
Full Service Manual
Submitter flyinbrian365 Submitted 02/17/2019 Category Polaris ATV
-
By GERONAMO308
Hi all am wondering if anyone has wrecked a 1992 quad runner, an has rear plastics available for it?.
Am hoping for red, although will take any colour if is in Perth Western Australia.
Any advice is greatly appreciated
-
By flyinbrian365
View File 2012-13 Polaris Sportsman 550 EPS X2 Service Manual
Full service manual
Submitter flyinbrian365 Submitted 02/15/2019 Category Polaris ATV
-
By colin james
View File 2002 Polaris Sportsman 700 Service manual
This is the factory service manual for the 02 sportsman 700 to have complete manual download all sectionset or just download the section you need.
Ch1 = General
Ch2 Maintence
Ch3 engine
Ch4 fuel system /carb
Ch5 boady/ steering / suspension
Ch6 pvt
Ch7 final drive
Ch8 transmission service
Ch9 brakes
Ch10 electrical
Submitter colin james Submitted 07/27/2018 Category Polaris ATV
-
By flyinbrian365
View File 2011 Polaris Sportsman 550 All Models Service Manual
2011 Polaris Sportsman 550 All Models Service Manual, Full service manual
Submitter flyinbrian365 Submitted 02/13/2019 Category Polaris ATV
-
-
-
Similar Tagged Content
-
By YamahaGrizzly
Complete Grizzly build
I built this Grizzly to preform at top ability in the mud! There is a few things that i am looking to change on the grizzly but well see!
Tires:
Gorilla Silverbacks 28x10x12 Front, 28x12x12 Rear
( https://atvtirescanada.com/gorilla-silverback-tire.html )
Snorkel Kit:
N2Deep Customs
( https://n2deepcustoms.com/ )
Bars:
Rox Speed FX risers and bars
( https://bit.ly/2TsRv18 )
Exhaust:
2r Racing tip
( https://amzn.to/2GgNdpE )
OR
( http://2rracing.com/ )
Clutching:
White Secondary spring. 8 - 16g rollers, 1.5mm shim
( bought at local dealer )
Rad Relocation kit:
( http://www.rubberdowncustoms.ca/ )
Lights:
12" Light bar
( https://amzn.to/2TrfZYy )
Rock Lights:
( https://amzn.to/2TpF9Xu )
Flush Mount LED headlight conversion:
( https://amzn.to/2D10Lm8 )
Yamaha front Bumper
( bought at dealer )
Handguards:
Powermadd
( https://amzn.to/2DQwmIR ) - guards
( https://amzn.to/2S2BCSq ) - mounts
3/4 inch spring spacers
(made myself)
Winch line:
Synthetic winch line
( https://amzn.to/2Gj1S3F )
-
By Guest Fox300exchic
If you know you're going to be bashing your quad's axle over rocks and rough terrain, tape it up. Take a roll of electrical tape and generously wrap the axle from the swingarm out to the hubs. Standard electrical tape will work, but the heavy-duty thick stuff is even better. When you are done bashing you bikr though the nasty terrain, you can cut the tape off and still have that showroom shine for your next out to the dunes, where you don't have to worry about getting dings!
Quad off-road magazine
-
By jtarus
I just purchased a Yamaha Kodiak 450 2005. Looks and runs good but a couple of little issues I need help with. The gear selector lights only work part of the time. It is Neutral and Park that seem to malfunction. If you have any suggestions it would be appreciated. Also the winch will not work. I have removed the switch and it does not seem to have any power to it. Any suggestions on this? Lastly does anyone know of a free down load for the manual?
-
By Alan Callison
OK everybody,I need some help here please. My 4 wheeler has got a bad wheel bearing I discovered while starting a brake job. Its on the left side. I've never done one and I need some knowledge how to go about it. Am I to understand I need to pull the whole axle out to do it. I've done it once on a car about 30 years ago,lol. I keep looking around for a repair manual but they're hard to find without having to buy it. I looked here on this site but apparently Im too junior a member to be able to download one right now.Bummer! One other question if I may.When I pulled the drum off the spindle a torrent of water poured out,the brake shoes were covered in mud along with everything else. I mean the drum had alot of water in it. The shoes were so locked up after I removed the springs I tried to rotate one of the shoes and it wasn't easy at all. I noticed whoever had the machine before myself had laid a bead of RTV around the back plate but apparently it didn't work. Isn't there some kind of gasket for this purpose. I saw it calls for a dust shield but surely this wont keep the brakes dry or will it. Thanks everybody.
-
-
Recently Browsing 0 members
No registered users viewing this page.
