Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

fatfarmboy

New-to-me 1989 Suzuki 250 4wd - not running

Recommended Posts

Just bought (Tue. evening) an '89 Suzuki 250 4wd that has been sitting out the last 5 yrs. It's complete, including the shift knobs, battery cover, and headlights. It has the optional cooling fan on it (probly stuck - didn't check), and the engine isn't locked up. Plastic looks good and isnt cracked. Racks aren't bent up. Shift lever works, the foot brake moves (needs oil - have to pull it up by hand), and there's black oil and no water in the engine sight glass. Guy was asking $125 and gladly took $100 for it. Anxious to get started on bringing it back to life. Been wanting one of these for years. As soon as I can get to it (working on a junky "Jackel" right now - Chinese Yamaha Timberwolf). I'm going to pull the tank off it and clean it, clean & possibly rebuild carb, put in new plug, and a battery, then see what happens. If nothing, will keep going until it runs. Feel free to respond if you want to, I'm mainly just excited and wanted to tell somebody. 

  • Haha 1

Share this post


Link to post
Share on other sites


That’s awesome that it’s all there too! Great find.   Going to be a lot of fun bringing it back to life.   Maybe post some pics.  

Share this post


Link to post
Share on other sites

i have a 1990 lt4wd wish it had the cooling fan but i put a small 12 volt fan on and switch,had a lot of trouble it would quit running except at idle all fixed now with help from these guys,dont block vent in front i did voltage regulater craped out needs to be cooled i guess.ive had trany apart to put starter clutch in best thing is to buy service manual good luck it will go any where in super low 4wd.

  • Like 1

Share this post


Link to post
Share on other sites

Yeah, I need to take some pics. I already took the goofy looking windshield off. I can't believe how good it looks for its age and for sitting outside a few years. The tires even have better than half tread and hold air. You mentioned having your tranny apart, Joseph - is hard to get to/take apart if I ever have to? Just curious. Oh, and it came with the factory owner's manual and a Clymer shop manual.

Share this post


Link to post
Share on other sites
Posted (edited)

Wow that’s a rarity finding a bike that old with tye manulas.   

Hopefully you wont ever have to get into a tranny project! 

 

Edited by Frank Angerano

Share this post


Link to post
Share on other sites


as far as trany goes not hard but takes time it calls for a puller but i new from heavy eqipment {retired mechanic} a air impack wrench 1/2" on nut it came apart have to be reallly carefull though.the reason i had to take it apart was because of starter clutch was shot.i all ways laid every thing on table with forks just like comes apart. make sure you get good atv oil before starting,amazon cheapest if you are in prime also for parts,napa oil filter comes with both o rings be carefull to install right way or you will be buying cover.good luck, oh take rear tire off when changing filter

Share this post


Link to post
Share on other sites

I would do the oil and filter first. It sat 5 years its due.

Share this post


Link to post
Share on other sites


Yep. Figured on oil change - engine/tranny and front differential. Just to see what would happen, I hooked up the battry leads to a lawnmower battry. When I turned the key, the neutral light lit up, the low beams work, and the speedo backlight works, too! Hit the starter button and a relay clicked right behind the battry box. Not sure what the easiest way is to get to that to check or change it. Hoping the Clymer manual that came with it will show me.

Share this post


Link to post
Share on other sites

Wow that’s a rarity finding a bike that old with tye manulas.   

Hopdully you wont ever have to get into a tranny project! 

If that relay is clicking when you press the start button then the relay is working. That battery may not be strong enough to turn the engine over or the starter is having a problem. You can put a tester on the starter wire and press the button to see if your getting power at the starter. 

 

Share this post


Link to post
Share on other sites

Thanks. That'll be one of my next steps - testing for power at the starter. I used a battery out of my riding mower - charged it first. When the relay clicked, I put the charger on the battery and set it for 100 amp start & hit the starter button a couple of times. Still clicked relay. This happened on my Chinese Yamaha recently. Turned out I had a bad ground. If it's not that, I may have to pull this starter and see if it'll turn. I'd like to have the starting system working so when I get the tank and carb ready, I won't have to pull the rope with my arthritic shoulder. 😉 

Share this post


Link to post
Share on other sites
21 hours ago, johniii said:

I would do the oil and filter first. It sat 5 years its due.

does the oil go bad from sitting?  (I mean, I would change it too if I were him) but I thought time didnt affect oil- just usage..

Share this post


Link to post
Share on other sites


2 hours ago, Frank Angerano said:

Be careful jumping it with to much amperage. You can do damage.   Wait for the right battery if possable.  

so what is the right battery?  Are all atvs compatible with each other?  Cars to atvs?  I have jumped many atvs and lawnmowers off my family's car...  always wondered if I was going to fry something..  And size- does the size of the battery mean anything or that just capacity (like a bigger battery is just more 12vs than a small battery..

Share this post


Link to post
Share on other sites

Jumping with a bigger battery like a car will work as long as the car really  is not running. 

 

What happens is if it’s running the amperage on a running vehicle is so much greater then what the atv puts out. What happens is the stator coil gets back fed from the higher amperage source and it burns the coil or the cdi or the regulator. 

Share this post


Link to post
Share on other sites

oooh thanks Frank!  Didnt know that- glad I didnt burn up anything all those times i did that- I was taught that you always turn the car on before jumping off of it...  but yea its the same on atvs- when off, the battery has +/- 12v...  when running, its like 13-15v...

Share this post


Link to post
Share on other sites

This also applies if your welding your frame or anything on the bike.  The stator coil and regulator should be disconnected as well as the battery. You will do damage.  

Share this post


Link to post
Share on other sites


I’ve seen some burnt up stuff big time. Wore harness melted butvtye stator was fine and vice verse.  It’s crazy how things get affected by electricity. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ajmboy
      With this cold snap, I noticed yesterday that the battery on my grizzly was a little weak. even clicked a few times before I got it to start. I'm thinking of picking up a batter tender/ trickle charger so was wondering what people use to keep their ATV battery charged up. I was looking at these on amazon. They both have good reviews.

       
      or this one

       
      Kind of like this one because if the accessory plug

    • By aj ford
      what is the best route to go as for the notorious  swing arm cracking on my 86 suzuki lt250r. any swing arm interchangeable.
       
    • By Brandi Nedley
      We just bought a used polaris sawtooth 2006. Any advice on pros and cons or things to look out for. were 1st time owners. basic maintenance?
       
    • By tom reed
      May be some of you guys can help me, I've got a 1990 honda four trax 2 wheel drive, the top end has been completely rebuilt. When I bought it barely ran, so I had everything redone BUT, it shifts good until the motor gets up to running temp and it starts getting hard to shift and the longer you run it the worse it gets, it will get so bad that it is almost impossible to get it into reverse. Does anyone know what wrong?
    • By JacobSlabach
      Theres a horse farm I work/worked at and they have a Rubicon (500cc)  think its a 04.  Its been having starting issues.  First time it wouldnt start, the owner said it had a new battery in it (this is about a year ago I guess..).  I replaced the solenoid and then the starter.  the battery was dead so I jumped it and then it started fine after the battery charged.  about a month later, same problem.  I swapped the solenoid back out with the old one(still had it)- nothing.  the owner had another battery she said was good, swapped that out and it fired up.  Now, today, same problem again... owner says the starter was sluggish and then the battery went dead.  Went out and jumped it again and it ran fine (its a carburated atv so its not fond of under freezing temperatures...).  the stater is working cause when I got there, the battery had 7-9v on it (multimeter said it was rising and falling (with the key on)).  I jumped it off  our van and rode it around for say 5-10mins.  when I shut it off again, battery is reading 14v with key off and 13v with it on.  thats as far as I've gotten..  I asked the owner to let me know if anything else happened later on..  What I'm wondering is if its just the battery, or maybe is the regulator rectifier not working letting the battery be overcharged cause it to die?  And then again, the bike could have sat with the key and headlight on overnight for all I know..
  • Similar Tagged Content

    • By Flanstone
      I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
    • By Christopher Williams
      Hello all, 
      i just rebuilt the top end of a 99 Bear Tracker 250 and it can’t get it to hit off of gasoline or starter fluid. Occasionally it will backfire. Right now I’m just trying to get it to fire off without the carburetor like I’ve done a thousand times before with other engines. Usually there is no response, but occasionally I get a backfire through the intake. ISeems like it’s out of time, but I don’t see how that could be possible. 
      Here’s what I know:
      1. compression 120psi
      2. all timing marks are lined up after numerous revolutions. 
      3. Strong spark. 
      4. Valves adjusted correctly. 
      Thanks in advance. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...