Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Wes Camp

1988 Suzuki 250r Quad Racer Seized

Recommended Posts

Posted (edited)

So I bought an 88 qaudracer real nice bike fired up 2-3 kick everytime. When I bought it the brake calipers were not on the bike the guy gave them to me In a box with parts to rebuild. So I HAVnt ever really rode the bike except a quick run testing gears when I bought and I started it and drove in yard not getting out of 3rd due to no brakes. I put it in garage turned it off. The following weekend I put brakes on and go to kick it and it’s seized. I did put it in high gear and rocked it back and forth and got it to kick a couple times. But has seized back up. Any ideas??? Could it be a kicker malfunction??

Edited by Admin
Added full atv info and issue to topic title. Moved to Suzuki ATV forum.

Share this post


Link to post
Share on other sites


Welcome to Quadcrazy @Wes Camp that sucks about the engine locking up. 

You should be careful about trying to rock the bike or to keep trying to kick start it. You could do more damage then good.  Your piston and rings may have went.

I would start by double checking the basic stuff first like the kick starter making sure nothings  stopping that. Then move to pulling the plug and see if the engine spins with the plug out. Don’t force it when trying that . 

If not then you may want to pull the head and cylinder off and inspect the piston and rings along with rotating the  crank to see if the main bearing is ok.  My guess is a piston and rings is needed. But just hope it didn’t damage the cylinder walls.   If you pull the cylinder and see a chunk of the piston missing then there you go.  

  • Thanks 1

Share this post


Link to post
Share on other sites

It happens. Crazy as it sounds but pistons don’t choose a time to go and I could be wrong but I’ve blown a ton of pistons and that’s what it sounds like to me on your bike.  

  • Thanks 1

Share this post


Link to post
Share on other sites


check the oil.  I had a bike that the guy said it ran perfect before he sat it outside three years ago, engine was half locked (popped lose and then spun like it should), but over those three years the bike accumulated water in the crankcase, everything was rusted.  Obviously your's isn't this bad because its running, BUT I would check the oil (this means drain it- its hard unless you're a pro to tell if there's water just by the dip stick), if its good and the oil is fresh, I would just pour it back in, if not, then I would change it.  But say there is enough water to lock up your piston, catch it now and save your engine!

and water can get in all kinds of ways from condensation to being stored outside to the quad being sunk...

Share this post


Link to post
Share on other sites

Well yes and no.   The piston obviously blew and blasted the cylinder walls.   If it’s not to bad you can bore it out and go a little bigger on the piston.  Going to need a new jet kit for the carburetor as well.  

Now, if the cylinder is shot then you can possibly pick up a used cylinder maybe from eBay and go that route.   Or buy an aftermarket cylinder set up.  

The metal parts that came off the piston went into the crank case. They can be flushed out.  Also you have to check the main crank and bearing for play. 

Have you noticed anything else that’s possibly damaged as well? 

  • Like 1

Share this post


Link to post
Share on other sites

Top and bottom being replaced. Cylinder bored out to 68mm. Crank, bearings, seals rod piston 

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By mrfartsalot
      i have a 1986 yamaha moto 4 200 and was wondering if i could put a 350 or 300 jug and piston on it to bump up the cc?
    • By StolenATV
      1987 Suzuki LT 80 and 2007 Honda CRF 50 dirt bike stolen out of my driveway on July 4th. Anyone with info that recovers them will get $400 no questions asked.
      Thanks
      The post Suzuki LT 80 Quad And Honda Dirt Bike appeared first on STOLEN 911.
      View the full article
    • By JacobSlabach
      So yesterday I picked up a 07 polaris sportsman 800efi stealth edition for 3k.  Will lead a pic ltr.  In good shape.  Here's what's wrong with it:
      The rpm needle doesn't work just like my other sportsman... not too worried ab that.
      The motor doesn't sound like it's running quite right and doesn't feel like it has much more power than my 500.  I'm thinking it needs a tune up and some fresh oil..  but also it feels like it's running rich.  It's a little buggy when you goose the throttle and sometimes farts when you let off (like I little backfire out the exhuast). I'm gonna check timing and valave clearence on the motor first but thinking of putting a tuner on it? Anybody got a suggestion?  Mainly looking for more power.
    • By John Dunn III
      Just bought a LT 230 anything I should watch for. It runs and drive good. Just don't want no surprises 
    • By Frank Angerano
      I’ve decided to post  a thread on the process of cleaning a carburetor and what’s needed in order to do it properly.    There are some members that are new to this and are not very versed in doing so. I want to help and feel this might explain things better. I would hope this helps you along.     We all have our own little tricks of the trade so I’m sharing my process on how i break a carburetor down, clean, reassemble and adjust it to peak performance. I welcome any other members input on this topic.     List of things I use:   Safety glasses !!!   Rags.   I like to use old white Tee shirts or I buy and always have a few white pillow cases from the dollar store on hand. The cheap ones.     I like to use a frisbee turned      upside down like a bowl to keep the liquids to a minimum on spillage to the work bench.    A set of cleaning picks and brushes or a piece of bicycle break cable, I separate the strands and use them to clean out the tiny holes in the jets. (Pic attached)     A can of gum out  carburetor cleaner with the small red tube that attaches to the spray tip.  (Pic attached)   A can of compressed air, the kind used to clean out keyboards on computers. It also has the small red tube that attaches to the spray tip.  Or a compressor if you have one with a blow out tip.  (Pic attached)   A piece of clean hose that I can connect to the fuel line port on the carburetor to test the float operation. About 10 inches long.    A few Q tips.   The process: I like to put the pillow case down on the work bench and spread it out flat.   This really helps in being able to keep track of parts. Especially because it’s white.     I use the frisbee because it’s small enough to keep parts contained and durable enough to deal with the chemicals and any gas that will come out of the carburetor while opening it up.     It’s important to make sure you keep track of where everything came off and where the screws and parts all go back.     I like to start at the bottom and pull the bowl off. I immediately spray the inside of the bowl down with carb cleaner until its about half way full and set it aside.   Then I take the float out and check it for any fluid inside. If it’s a white color float you can hold a flashlight under it and see through it for any fluid inside.  If it black just shake it up and listen for fluid inside. No fluid inside is a good thing !    When the float comes out the fill valve needle will come with it. I take that needle and put it in the carburetor bowl that I filled with carburetor cleaner. This way it soaks for a bit. I do the same thing with the jets also once they are unscrewed and out toss them into the bowl to soak.    Take the air/fuel mixture screw out and soak that as well.  Side note: the air/fuel screw should have a screw, spring, washer and o ring.    After all the jets and parts are out and soaking I like to take the carburetor cleaner, use the small red tube and stick it in all the little holes/ports on the carburetor and spray.   I do this while it’s in the frisbee. This way there is no mess. I look to see where the spray pressure comes out on the other side of that port.   Once this is all done I start running my brushes and cleaning tips gently through all of the holes/ports and spraying it again with the carb cleaner.  After I feel I’ve seen a clear flow of fluid through all the openings I spray them with the can of air the exact way I did with the carburetor cleaner. This will blow out any left over junk that’s still in the carburetor.   Check the choke operation is working properly and spray it clean. Most choke devices are easily cleaned up so hit it and move on since they are mechanical and it’s just a matter of freeing them up, spraying with cleaner and lube.   There are multiple types of chokes but many of them for the most part are mechanically operated.    Once this is completed I wipe the entire carburetor down good and blow it clean and set aside.     I then start working on the jets one by one. Start by running the cleaning tips and brushes through all the tiny holes making sure they are all clean. Hit it with the carburetor cleaner and then air. I hold a flashlight to it when it’s done so I can make sure all of the holes are clear. I set all the jets aside on the work area.  Do the same thing for the float needle and air/fuel screw.    Now once this is all complete you can set the frisbee aside and start to reassemble the carburetor on the clean white surface.   I start by running a Q tip in where the fill needle sits into the carburetor. Some carbs have a small o ring that needs to be clean for proper seating of the fill needle.     Carefully reinstall the jets where they came from and do not strip or over tighten the jets and use the proper size screwdrivers when removing and reinstalling the jets.    Reinstall the air/fuel mixture screw and set it to what’s called out in the manual for that bike.    Install the float and fill needle assembly.    Now in order to test that float I like to take that piece of hose I mentioned and connect it to where the fuel line gets connected to the carburetor. I then turn the carburetor over to the upright position and blow into the hose. You should hear air coming out of the bottom of the carburetor. While blowing, lift the float up and the air should stop.  Let it go and the float should fall down opening the fill valve and you should hear air again.  The air should stop about 3/4 way up when raising that float while your blowing air into it.   If so then your good to go. If not make an adjustment    Set the carburetor down, take the bowl and empty it.   Clean it out and scrape/wipe any old junk inside and blow it out good.   There is a screw on the outside of the bottom of the bowl. Remove it and clean it out and reinstall.     Turn the carburetor over and reinstall the bowl. Tighten the screws in a crisscross pattern so the bowl seats evenly.     I like to put the hose on one more time and do a float test to make sure it’s opening and closing properly. All you have to do is blow into the hose and run the carburetor  upside down to see if the air stops.     Reinstall the carb and you should be good to go!    All pics of the items I use are attached below.   If you understand this great. If not ask away! Don’t be shy and don’t cut corners.   You will only wind up pulling the carburetor off of the bike for the third and forth time before you get it right.    The last thing to be discussed is dialing in the air/fuel screw when your finally put back together and running.  This is a relatively easy task.   Again I hope this helps!    Frank.     


  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...