Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Jcolgin

1998 Yamaha Big Bear Tail Pipe/Spark Arrestor Broke

Recommended Posts

I have a 1998 Big bear 350...the tail pipe/spark arrestor is broke in the exhaust....how can I get it out to replace it? And what's the best way to get the new one in?

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Colby Calk
      I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
    • By MarkinAR
      So this 98 Big Bear is my new project.  While I'm waiting on a few parts to show up, I'm working on a few small things.  I can shift 1-5 just fine, no problem at all (keep in mind, this is not running yet so just manual shifting sitting still).  However, I can't shift from 1-neutral.  I can hold down on the foot shifter, rock it a bit, and it will disengage the clutch so i can push it around in neutral as long as I keep pushing down on the shifter.  However, it will not downshift to neutral and stay there.  I know BB's have had some shifting difficulties in the past, but before I dive into this, have any of you fine folks encountered the same issue?  I'm tempted to just adjust the linkage a bit since these have an external linkage, but thought I'd toss the question to the group and see if there are any common issues to look for.
      Thanks guys...
    • By Wolf Studios
      Hi guys so I'm looking for any help or advice with a yamaha big bear 350 1997 (i think) it's fairly dirty and just been say for many years, boss says it's a non runner and I've tried and it will not start, ideally would love to do it up and get it running but have been told the engine has gone, cannot find a new engine anywhere. Anything I should check first before just taking the entire thing apart? 

    • By MarkinAR
      Picked this gem up today for two Benjamin's. Bike is complete, just worn out all over. Should be able to get the plastics back green, need to fix the shifting as it doesnt go into neutral, carb has been off 6 months but the intake was plugged off and he had an OEM carb that just needs rebuilt. Rear brake drum is completely seized in the open position. Normal relay, solenoid, wires are trashed. Think itll take about $100 to get it rideable which isnt bad for a $900ish bike. 

    • By MarkinAR
      Working on my oldest son's buddy's 2000 Big Bear.  He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit.  It starts and idles like a champ, but dies and wants to backfire with any throttle at all.  I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle.  This one has fuel/air screw, low speed jet, mid jet, and main jet.  I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same. 
      Two questions I guess:
      1. Does it sound most likely trash in the off idle circuit?  This one has a few more passages and jets than I'm used to...and a darn diaphragm.
      2. It now really wants to leak at the bowl drain screw.  It doesn't seem to tighten enough to completely stop the flow.  Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper.  First for me.  Any idea here?
  • Similar Tagged Content

    • By Wolf Studios
      Hi guys so I'm looking for any help or advice with a yamaha big bear 350 1997 (i think) it's fairly dirty and just been say for many years, boss says it's a non runner and I've tried and it will not start, ideally would love to do it up and get it running but have been told the engine has gone, cannot find a new engine anywhere. Anything I should check first before just taking the entire thing apart? 

    • By MarkinAR
      Working on my oldest son's buddy's 2000 Big Bear.  He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit.  It starts and idles like a champ, but dies and wants to backfire with any throttle at all.  I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle.  This one has fuel/air screw, low speed jet, mid jet, and main jet.  I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same. 
      Two questions I guess:
      1. Does it sound most likely trash in the off idle circuit?  This one has a few more passages and jets than I'm used to...and a darn diaphragm.
      2. It now really wants to leak at the bowl drain screw.  It doesn't seem to tighten enough to completely stop the flow.  Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper.  First for me.  Any idea here?
    • By Walter Awe
      I HAVE a 2002 big bear 400 4x4. I have two wires atacking to the front of the carb. What are they for?
    • By Shook
      Hi I have a 2000 big bear 400 and i just put a new carburetor on it and it idles fine but when you try to accelerate it sounds like it is going to die, so when it sounds like it is going to die I will give it more throttle then it will go just fine.
    • By Nigel Bourn
      I’ve just bought one of these and came here looking for a service manual
      Mine has an air cleaner that I don’t seem to be able to find, it has round ends with square tabs on them, any ideas?
       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...