Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Steve Simpson

Head gasket Suzuki LTZ 400

Recommended Posts



Most cost effective would probably be a complete kit through a site sponsor here, at suzukicentral.com, or ebay

Share this post


Link to post
Share on other sites

I would also recommend ebay, just be careful to double check all of the specifications. This will ensure you get the right kit the first time.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Meg Sam
      Hi I have bought a Bashan bs200s-3 and I am wondering where I can buy parts for this as I need a full new wireing loom also does this model have reverse gear?
    • By bren7176
      So time to purchase the new piston and rings for the 1995 Sportsman 400 . Looking for some input on this like what would be the best to buy ....
       
      thanks
       
      Brendan
    • By Hellraiser69
      Just got a new to me, 99 Kodiak w/ plow and an extra set of tires for dirt cheap. I'm curious where you guys purchase your parts for your older ATV's? Google is great to find parts, but I'm hoping you guys have some stores, online, that you prefer on a recommendation basis. I've already purchased my tune-up items, but the brakes need some work and I'll likely end up having to replace the steering stem bearing, front CV axles and a few other things down the road.
    • By MarkinAR
      So just as a general FYI, it might be good to check replacement parts before installing.  If possible, check clearances with a micrometer before going through the trouble of assembly.  I say this as I bought a new driveshaft yoke for a Kodiak because the ujoint dropped a cap and got the yoke in a bind...blowing the yoke and middle drive gear to shreds.  So I replaced the middle drive gear and bought a new yoke and ujoint kit from Caltric.  Caltric is usually pretty solid replacement parts.  The new yoke however was a good 4mm too narrow for inside lock ujoint caps.  Disappointing since it came as a kit from Caltric.
      Ended up taking an angle grinder to the new yoke and thinning material off to get it to the needed 41.25mm opening size.  Sucks having to disassemble everything again and start over but my fault for trusting replacement parts.  Nearly 40 years of turning wrenches and I made a rookie mistake.
  • Similar Tagged Content

    • By Dave HRABCSAK
      2004 LT-Z400 carburetor Question. Can someone please tell me what this screw does? and and what it's purpose is? (picture attached) Thanks

    • By Shonko72
      I am looking for a 2003 LT-Z 400 left engine case anybody have one or where I could find one PLEASE Help
    • By LTZ-Zach
      So i was riding the other day and my quad randomly shut off. It started back up and ran completely fine for a little while and then it started idling terribly.
      I cleaned the carb and changed all the jets and everything except the float due to the rebuild kit not coming with one and it actually runs worse then it did before.
      It will run and idle decent now but when I give it gas it dies.
      Does anybody know what could be wrong?
      I also changed the spark plug and air filter along with the oil and oil filter.
       
    • By TJ Verrett
      Was given a Yamaha 250 Timberwolf. The guy said he thought the engine was blown. However
      after talking with him some more what he described sounded like a blown head gasket.
      Description was " It was using a quart of oil per day, then while out riding it began to smoke a lot,
      afterwards it lost power and died". I'm a small engine mechanic! and this description fits with blown 
      head gasket. Any thoughts on this?
       
    • By jamesbailey8809
      I have a ltz400 2012 model that will not start only turns over I was riding in 2nd gear and it was lacking power I hit the gas and it just shut off on me would not start any more before it shut off it started ticking does anybody know what is going on when I try to start it now it only turns over like it has little compression when you give it gas the compression goes away and only the starter turns
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...