Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

anthony zimmerman

Sportsman 700 coolant in oil

Recommended Posts

Found coolant in my engine oil, I pressure tested the cooling system with oil drained and drain plug still removed, I found if bolt on mag side cover  that goes through the middle of the gasket on coolant port is removed antifreeze leaks out. Has anybody had this issues, is mag cover gasket leaking coolant into the engine oil?

Share this post


Link to post
Share on other sites


That is the same side as the water pump correct ? If so then yes you would see coolant leaking into the engine if bolts are removed from that cover or if there is a gasket failure.    

Share this post


Link to post
Share on other sites

how do you check for coolant in oil?

Share this post


Link to post
Share on other sites

@JacobSlabach if the coolant is pure and clean you will clearly see the green or whatever color coolant blobs in the oil.   If it’s mostly water then you will see the standard grayish color with some of the coolant streaks in it.  

There is also a pressure tester cap that has a pump connection on it to pump air into the system to pressure test it.   

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Venom
      Hi All,
      Hoping someone will be able to help.
      I have a 2006 Kawasaki Prairie 700 with twin Keihin Carbs CKVR D32. The Rear Carb is leaking out the side during cranking. it is not the float bowl overflow. It is on the opposite side of the carb from the diaphragm. 
      I got this bike not running and someone had already messed with it. I took the carbs apart , cleaned and rebuilt. Everything went pretty easy.  It looks like it could be missing a small tube between the carbs but I have all of them listed in the service manual installed. See the pic for where it is leaking from...
      Any help would be much appreciated.. Thanks.
       


    • By Eddie Lambert
      So I picked up a Cannibal that has been sitting for many years. I wonder if anyone can tell me where that vacuum port is on the engine. I’ve found the one to the air box, pressure regulator, and ecu but can’t seem to locate the one on the engine. Thanks in advance for any help. 

    • By Steve Simpson
      Any suggestions on where to buy new parts want new jug piston rings would like to go wiesco big bore 
    • By joninak
      Well, it overheated then started blowing white smoke!!
      I have it torn down & the cylinder appears to be warped. Going to have the head checked out next but in the meanwhile... Does anyone have the torque sequence/specs for the head bolts??
      TIA
       
       
    • By bradleyheathhays
      I bought a 2011 Crown Vic with 300k miles 12 mos ago and I'm wondering how to approach servicing the timing belt. I know very little of it's past maintenance records other than what I've done with it this past year. Basically I'm wondering if I should go ahead and attempt to replace it now, or wait til something starts to go wrong. I don't know how timing belts typically go bad...if they just break or start to stretch or what. If this is an interference engine I'm imagining a fairly bad event so I'd like to get educated and be pro active about it.

      Second...Scotty Kilmer teaches that the worst wear an engine sees after changing the oil is before the oil gets pumped back into the filter and then into the engine components during the first engine restart. But he says if you disable the ignition spark somehow when cranking for the first time again, the lack of combustion in the cylinders helps with reducing this kind of wear quite a bit. I don't have an owner's manual and I'm not sure what fuse to pull to disable combustion ignition, or if removing a fuse would be the best way to do this. Any opinions on how this should be done?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...