Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

bradleyheathhays

How to disable my airbag *gasp*

Recommended Posts

So my Mom drives a 2002 Ford Taurus that I believe has one of the Takata airbags that have been killing people. So far her car hasn't been recalled for the airbag, but I know this recall is being done piece meal as they can't do them all at once, and since the recall applies to the year right close to hers I suspect hers eventually will be recalled as well. Either way I don't want to take the chance, and here's why...

The explanation for why these things are going off is there's some defect in the manufacturing that when the air bag is exposed to humid conditions and lots of temp fluctuations, something in them weakens and there they go. Mom's Taurus has a windshield leak so, even though it's never smelled, there's always been a virtual puddle of water in driver's side floor board. So the inside of the car has always been humid, just like in the airbag explosion scenarios.

So, for the time being, until she gets into another car, I'd like to disconnect her airbag to be on the safe side. She is an amazingly vigilant driver, never even a speeding ticket, and the risk of her rear ending someone is virtually non-existent.

How would I go about disabling an airbag on a 2002 Ford Taurus?

Or, alternatively, how do I open the steering wheel column, or front of the steering wheel, which might be part of the disabling process itself, and identify if Mom's airbag is indeed one of the defective types?

 

Share this post


Link to post
Share on other sites


I would never advocate for disabling a safety feature like an airbag, but do understand your concern with all the Takata recalled airbags.

Vin # check https://owner.ford.com/service/frequently-asked-questions-regarding-takata-airbag-inflator-recalls.html

I would first look on youtube to see how yo can remove or disable.

 

Share this post


Link to post
Share on other sites

I also agree about disabling a safety feature. Removing the airbag might cause a problem when the car is recalled since it was removed. It also may not pass inspection with the airbag missing. I know in PA the airbag must be present to pass inspection. Since this is a known issue, I am sure there are Youtube videos in how to deal with this.

Mike

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tom Walters
      Working on 2002 700 sportsman in shop. Engine has no power. Pops and backfires at 1/2 throttle and above. Carb is clean. Good fuel flow. Checked stator output with DVA. 19v on charge coil. 6v on pulser. Would like to know if this is cdi related.
    • By Jeff011366
      Hello,
        Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
       
        My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires....  Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
        It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
       
      Thank you in advance for sharing your knowledge.
      Jeff
    • By Summer Warren
      Hey I just recently bought a 2002 Kawasaki Bayou 220 when you shift it jumps a lot and while it’s riding it it’s jumping as well but won’t stay started when you let off the gas Could somebody tell me what could possibly be the problem? Thank you
    • By bodatiouskid
      Have a 2002 Kawasaki 650 Prairie.Have just had carbs rebuilt($950 bill) & it still pops back through carbs.Mostly at 1/4-1/2 throttle.What can I tell mechanic to do when I take it back?(A Kawasaki dealer mechanic)
    • By Rcndn
      I have a 2002 yamaha bigbear 400 4x4 with a seized engine. I was able to free the piston with the old "fill cylinder with oil and let it soak" and it worked. So I bought a top cylinder rebuild kit , but now I have no idea the process to fix this . I need a service manual.... 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...