Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

caperwing

1990 suzuki LT-F250 4x4 rear axle

Recommended Posts

I need to get a rear axle for this machine.  Are 2wd and 4wd the same axle?

Are left and right the same axle?

What years will fit a 1990?

Thanks

Share this post


Link to post
Share on other sites


I would think 88-90 or 92 would work. But I would check around online. Look at the parts houses and compare some of the parts diagrams. Are you looking for used that you want to know what range of years would work?

Share this post


Link to post
Share on other sites

Thanks, That's what I'm doing now but getting conflicting numbers. I'll just keep digging.

Share this post


Link to post
Share on other sites

I found a used one but will take 2 weeks to get here. The axles are the same from 88 to 02. left and right are the same and the axles are the same either 2 or 4 wheel drive. Maybe someone else can use this info.

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ed Zeppeli
      I have some wobble in my right rear wheel. Too much wobble.
       
      So I've torn into it and will need two bearings and two (different) seals. I'd like to get them locally if possible but need to know the number on the sides of the bearings and seals as I don't know that my bearing shop can source them by vehicle model. I'm told they're very common bearings.
       
      Any idea what the numbers are if mine end up being illegible?
       
      Thanks,
       
      Warren
    • By joseph
      my atv will start right up will idle fine soon as i try to throttle up engine dies,i have changed gas,new fuel pump and lines great compression 188 lbs.new coil new spark plug adjusted valves dont know what to do also rebuilt carb,any help wanted
    • By kgrant
      Fixing up a 1998 King Quad 300. The rear brake was locked up, and the owner tried to force it free and snapped the axle.
       
      I disconnected the brake cable, and tapped on the backing plate with a soft mallet to get the brake freed up. When I pulled off the brake drum a bunch of nasty rust water came out.
       
      Once I had the axle out, I popped the boot off so I could see the inner u joint so I could phase/synchronize it with the outer. There was a flat steel disc floating around in the boot, looks like it used to be pressed into the end of the axle. Glad I got that out of there before it munched up the joint.
       
      The book says the yokes should be aligned, I couldn't get mine aligned. They were always 7 degrees off from each other. A bit frustrating, maybe that's within the tolerance limits?
       
      But I got it all back together and it runs great.
       




       
       
    • By Gerry Davidson
      Can anyone help me , I did the rear brake pads and rotor but cant find the brake fluid reservoir.   The front in rite there but cant find the back . 
    • By Venom
      Hi All,
      Hoping someone will be able to help.
      I have a 2006 Kawasaki Prairie 700 with twin Keihin Carbs CKVR D32. The Rear Carb is leaking out the side during cranking. it is not the float bowl overflow. It is on the opposite side of the carb from the diaphragm. 
      I got this bike not running and someone had already messed with it. I took the carbs apart , cleaned and rebuilt. Everything went pretty easy.  It looks like it could be missing a small tube between the carbs but I have all of them listed in the service manual installed. See the pic for where it is leaking from...
      Any help would be much appreciated.. Thanks.
       


  • Similar Tagged Content

    • By mmmPUDDIN
      I've had this machine for 2ish years, has ran great up until winter. Sometime during then, I managed to break the exhaust right before the muffler. The summer before it had a hard time idling, but we fixed it by cleaning the carb, and messing with idle. Near the end of last year, the only way for it to fire was the have full choke, and full throttle, and the engine bogged down and you had to keep on throttle for 25mins. Over winter, the throttle had dislocated, and I got it back in place. We got it running, and all was good. Spring came along, and now it doesn't start at all. A fluid is coming out of the exhaust, and I'm told it could be water from over winter. I checked the airbox, and the air filter isn't for this quad, it also is barely sucking air. There appears to be little to no compression, based on this. I'm pretty sure the engine is flooded, as the spark plug produces a spark, but is oxidized. I don't know how the previous owner treated it, or when it's last oil change was. A bolt on the engine has either oil or gas seeping through it,abd was loose. I tightened it and it consisted. The engine is basically positioned in the rear, and it needs a good clean, I don't have a pressure washer, so I can get the built on dirt off. any recommendations on how to get the beast started again?
    • By caperwing
      I just got this quad a few days ago and finally got it running. It has oil leaking and it seems to be coming out around a cylinder bolt. Not the valve cover but just below and to the rear. Is there supposed to be crush washers on that bolt? and what are those bolts supposed to be torqued at?
      Thanks
    • By GERONAMO308
      Hi all am wondering if anyone has wrecked a 1992 quad runner, an has rear plastics available for it?.
      Am hoping for red, although will take any colour if is in Perth Western Australia.
      Any advice is greatly appreciated
    • By bfh42
      I am looking for an LT-F250 and I want to know if there are any common problems that develop over time so that I know what to look for when buying. Any help would be greatly appreciated.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...