Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Gary Patch

Linhai 300 idle speed

Recommended Posts

Still waiting for new cdi frank but have tested out new regulator with voltmeter and is spot on but still blows main fuse immediately ,the old one does not but I tested that out and have no reading on it at all any ideas ,,does seem like a short to me 

Share this post


Link to post
Share on other sites


Hey Gary, I was looking through your wiring diagram and highlighted a few things. 

Please verify that I’m looking at the right diagram please. 

As a side note have you tested your stator coil to see that it’s not dead shorted. Reason I’m asking is based on your wiring diagram it looks as the stator goes directly to the regulator/rectifier. So I would unplug the stator and do a quick test from each phase to ground and see if you get any sort of continuity on the tester. You shouldn’t get any reading from any of them yellow wires to ground. If so there a problem within the stator. You can also unplug the stator and try the regulator again and see if it blows a fuse.

Then if that checks out ok I would disconnect the battery and put one lead of the tester to the ground and start touching various parts of the red (hot wire) that comes from the fuse block going to the regulator as well as other areas that carry a 12v hot lead looking for a short.  So make sure your tester is on continuity/ohms setting. I like to use a tester that beeps when there is continuity. 

Also test the starter wire, starter relay and the line going back to the battery to ground for continuity. This way you eliminated everything that could be a short leaving only a fault in the cdi.

lastly the third pic I circled the on off switch in blue it appears the wire is listed as “P” so maybe (purple?)   it comes from the on/off switch and if it’s disconnected it appears it will isolate the cdi unit from the rest of the system. So try to find that wire around the kill switch and unplug it. Install the new rectifier and see if the fuse pops. 

Im in and out of WiFi so if I don’t get back right away I’m out of range. 

Let me know.

good luck   

 

A03A715A-F591-4F93-B265-1F7609755D65.jpeg

3F24B01C-C98E-48B6-881B-1DEE2D42016B.jpeg

D977BD0A-6BFB-46F6-AD5A-D4A4F715BF35.jpeg

  • Thanks 1

Share this post


Link to post
Share on other sites

Much thanks for helping with this I will try all of this when I have time ,I did try unplugging stator and bypassing ignition and plugging new regulator back in so I guess it's not stator that's nearest manual could get on a bike 2 years younger but wiring looks same.thanks again for your time

Share this post


Link to post
Share on other sites

Ok so that eliminates the stator. I’m surprised that one wire brings the cdi and the rest of the system together.  Find that wire coming from the on off button disconnect and see what happens.  I’m still hoping it’s just a mater of  an oem reg/rectifier that’s causing all this. 

Share this post


Link to post
Share on other sites

Hi frank ,I am getting a continuity reading between negative battery and positive solenoid with positive lead disconnected from battery is this showing a short sorry if daft question not good on electrics 🙃

IMG_3903.JPG

Share this post


Link to post
Share on other sites


Posted (edited)

Ok so unplug that plug from the relay and test it again. If you don't get a reading then you start tracing the lines off of that plug back. If you do continue to get a reading yiur going  to have to trace that wire your on back.   Why is that wire your testing black????

Edited by Frank Angerano

Share this post


Link to post
Share on other sites

And from positive on starter motor showing continuity ,the on off switch is not on this bike that is the only bit of the wiring diagram that differs it does have a switch on front handle bar brake that has to be operated for starter button to operate 🙄

That wire is black as I ordered wrong colour hence the red insulation tape I put on it lol

Share this post


Link to post
Share on other sites

The brake lever should just be a safety to close the start circuit.   That wire your  testing goes to the starter ?  If so disconnect it from the relay so it’s independent and test that wire and the relay separately.

I’m wondering if one of them wires is hot or burnt up someplace or if something failed inside the starter. 

Separate all of them and test individually. 

Share this post


Link to post
Share on other sites

Just continuity on starter now not on solenoid ...sorry about all this frank but glad of the help

IMG_3905.JPG

Share this post


Link to post
Share on other sites


No worries please it’s my pleasure to help. Ok so disconnect the wire from the starter, test again and see if that wire fails. And then test the bolt lug where the wire connects on the starter. If the wire fails than it’s shorted against the frame someplace. If not then the starter may have a failure. 

You can also take the wire that’s coming from the starter and very very quickly tap it against the positive terminal on the battery to see if the starter spins. If it sparks like hell straight away stop. 

Share this post


Link to post
Share on other sites

Was just starter showing continuity which was replacement so removed and fitted original which shows no continuity engine turns over ok but still no spark have to wait for new cdi to arrive I suppose could it have been the short in starter destroyed the cdi ?

Share this post


Link to post
Share on other sites

Yes sir. I think that’s correct. It’s possible that the momentary draw could have done damage. I hate to say it but definitely a possibility. Have you tried any of the new regulators ? And put it all back together so see how the fuse holds up ?  

Share this post


Link to post
Share on other sites


No old one does not pop fuse but don't get any reading testing old one with volt meter new ones test out OK but blow fuse 

Share this post


Link to post
Share on other sites

Ok so basically now it’s just a matter of new parts coming ? Cdi and regulator ? 

Why did you swap out the starter in the first place if I may ask ? 

Share this post


Link to post
Share on other sites

Seemed to be not turning over fast enough but no difference with new replaced solenoid too ,was going to leave regulator for now as it did start and run with regulator un plugged

Share this post


Link to post
Share on other sites


Could there be a short. On charging circuit causing new regulator to pop fuse not had chance to test everything with continuity yet ?

Share this post


Link to post
Share on other sites

I would test everything including the stator.  It can’t hurt to run some tests while you have things open.  I’m just not keen on the cheap regulator you have. This way you eliminate all loose ends.   

Share this post


Link to post
Share on other sites

Just been retesting frank and original starter is now showing continuity but there are 3 what I take to be ground wires attached where one side is bolted on as per pic also getting this reading from end fuse as per pic but no continuity beep 

IMG_3906.JPG

IMG_3907.JPG

Also plugged in new regulator while starter is isolated and still popped fuse 🙄

Share this post


Link to post
Share on other sites

Ok I’m  back. So that red wire on the starter is clear yes ? No shorts and no continuity from red to ground ? 

Tye three wires you see are ground wires. No issues there.  

so I would go after that “P” wire coming off the kill switch and disconnect that and see what happens.  This will isolate half of the system. It’s the one I circled in blue on the diagram.   

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Shane Pillar
      Talk about what kind of atv you have and what you do with it.
    • By fox300exchic
      Let's hear all there is to know about you ladies! Where your from and where you've lived. Kids or no kids. What you do for a living. Why you ride and how you got started.
    • By davefrombc
      View File Quad Runner 250 King Quad 1987 - 1998
      Service manual  for  King quads  250  and 300
      Submitter davefrombc Submitted 01/28/2017 Category Suzuki ATV  
    • By MarkinAR
      Working on my oldest son's buddy's 2000 Big Bear.  He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit.  It starts and idles like a champ, but dies and wants to backfire with any throttle at all.  I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle.  This one has fuel/air screw, low speed jet, mid jet, and main jet.  I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same. 
      Two questions I guess:
      1. Does it sound most likely trash in the off idle circuit?  This one has a few more passages and jets than I'm used to...and a darn diaphragm.
      2. It now really wants to leak at the bowl drain screw.  It doesn't seem to tighten enough to completely stop the flow.  Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper.  First for me.  Any idea here?
    • By Ryann Racho
      So Id say about 2 years back I bought a 2013 Polaris Sportsman 500 H.O. off of my uncle. It ran perfectly, nothing wrong at all. I usually go mudding with it or just ride trails with buddies. So as you would assume, the quad is quite dirty from sitting for a few weeks.
       
      STUTTERING PROBLEM: I noticed one day out of nowhere that in high gear at 15-20 MPH, I was already maxed out at 4500-5000 RPM  It would get to 15-20 mph, max out on rpms and start sputtering. It sounded like it was basically acting like it couldn’t go any faster than this.
       
      IDLING PROBLEM: I was fucking with the carberator the other day maybe thinking that is causing my sputtering, and now my idle will shoot up to 2600 on start usually, then I will turn the throttle adjustment down to the normal 1400. The rpms with then fluctuate 10-30 rpms back and forth repeatedly, it will then run for about another 30-60 seconds and the RPMs will slowly drop to about 900-1000 RPM and stall out. I replaced the carburetor and everything seems to be working perfect on that, no leaks and what not but it’s still acting strange. Also, I’ve noticed that when looking into the Electronic Throttle Control that two plates that aren’t supposed to touch have to be WAY past touching to even try to fire up. Even when set at a wide open throttle like that, I still have to give it some throttle to get it to fire up.
       
      Here is what I have done so far: 
      Checked the belt and clutch
      Changed out spark plug (Last one was covered in carbon)
      Cleaned the intake and air box
      Replaced the carburetor
      Replaced the inline fuel filter
      Checked that all lines on carburetor are connected into the right spots
      Checked If intake boot was cracked (Not from what I can see)
      Unhooked and reattached new carburetor (About 4-5 times)
      Cleaned battery terminals and battery off
      Shut on and off Gas Line Cutoff Valve
       
       
       
      My next thoughts are that maybe the TPS is fucked up or maybe the Spark Arrestor is plugged with mud. I was thinking tomorrow to purge the exhaust and also check the ohms output on the TPS.
       
      ANY HELP IS GREATLY APPRECIATED. I HAVE BEEN BATTLING THIS FOR WEEK AND REALLY WANT TO GO RIDING. THANK YOU!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...