Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

Posted (edited)

2012 Rancher ES-- only when driving in 4x4 when I get to about 15-18mph there is a loud clunk in the front end and a hard downward jerk. Its almost as if its trying to downshift itself. It doesn't do it in 2 wheel drive.  I have checked the angle shift sensor and applied dielectric grease to it, changed the front end differential fluid (the old still looked good and clean) checked and adjusted the clutch. Hopefully someone can give me some more ideas. 

Edited by Jeni Lynn

Share this post


Link to post
Share on other sites


Have you taken the differential cover off and inspected everything ? Also try to get the bike off of the ground (all four wheels) safely and put it in 4wd give a little throttle maybe you can listen in and see what’s happening.   

Share this post


Link to post
Share on other sites

haven't taken the cover off yet. I read on a different forum to check the psi in your tires that it could put stress on the front end. Mine were very high so I let air out to put it back at Honda Specs.  It seemed to help a. little... but now its more prominent when I'm slowing down.  

 

Share this post


Link to post
Share on other sites

Unfortunately your going to have to go through all of the components of the drive train to see what’s going on. Inspect everything, drive shafts, universal joints etc. 

You could be doing more bad then good by running it.  I don’t think that the tires would do that but what I would double check and super important is the size of the tires.  If the fronts are severely worn out it could cause a problem because 4x4,s must have all four tires rotating at the same time.  So if one set of tires are worn out the tires essentially become smaller and rotate faster then the others. That can screw up the 4x4 

last thing I would recommend is double checking all of your motor mount bolts, shock mounts and bushings etc. make sure nothing is jumping/banging because of a broken or missing bolt.  

Share this post


Link to post
Share on other sites

ok thank you.... i'll get on that and let ya know. Thank you

 

Share this post


Link to post
Share on other sites


Your welcome.

I hope it’s something relatively simple.

Any questions you might have ask away.

Also post some pics as it makes it easier to visualize  something with a pic to help you out and don’t be shy there’s no such thing stupid question related to a quad repair. 

Good luck and yes please keep us posted.  

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ajmboy
      Just got this one and am sharing...

      Visit 4wheelparts.com Use Code: POLARISORV at checkout *Exclusive offer ends 6/17/19 at 11:59 pm CT
    • By Aaron Ruiz
      Hey I'm new to the Forum but I just wanted to talk about my Scrambler I just picked up and when I first picked it up I thought it was okay but after I got home and everything I noticed it's very hard to shift into drive neutral reverse it is possible to shift into those gears but it's very stiff like and it takes a lot for it to actually engage to move forward. In Drive when I press on the gas it takes a while for it to actually start moving in the RPMs go up before it starts moving I inspected the belt it looks fine to me I checked the transmission fluid and it was low so I put some. I just hope transmission is not out just curious if you guys have any ideas
    • By RockOn
      So I bought a 2001 Quad Runner 250 for my son/wife. Sorry I run a Grizzly 660.
      I’ve rode it many times with no issue.
      My son’s first time out, I could always hear him but feeling he ran it red line in first gear a lot.
      So this is what it was doing during/end of the 2-3 hour ride:
      - halfway though noticed smoke (oil) coming from front of the motor sort of under exhaust manifold. Once back at the truck, it was really noticeable. Definitely oil burning off. I’m thinking from the top end maybe.
      So quick inspection:
      - No leaks or seepage of oil that I could see
      - I pulled the plug and it’s black but not wet
      - No blue/white smoke in exhaust
      - seems to still ride fine
      - Engine still has plenty of oil
      But now that I’m looking at it back at the house - it’s a hard/won’t start when hot. It starts right up cold no problem but once it stalls when hot, have to let it sit for 10-15 before it will start again.
      It wasn’t idling before that trip so I jacked up the idle a bit as well but I think that’s a carb clean/adjustment but...
      Any input is appreciated.
      Thanks for any help.
       
      Sent from my iPhone using Tapatalk
    • By StolenATV
      Someone broke into a barn located at the residence by prying the door open around a lock and removing the four wheeler. It did not have a key with it so there could be damage to the ignition or had the key tumbler replaced. It had a big NC Hunter’s Safety sticker on the gas tank. This belonged to my daughter who loved to be a country girl along with her cousins. Image is a stock image
      The post Stolen 2013 Honda Rancher – Green appeared first on Stolen 911.
      View the full article
    • By Jeff011366
      Hello,
        Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
       
        My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires....  Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
        It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
       
      Thank you in advance for sharing your knowledge.
      Jeff
  • Similar Tagged Content

    • By Summer Warren
      Hey I just recently bought a 2002 Kawasaki Bayou 220 when you shift it jumps a lot and while it’s riding it it’s jumping as well but won’t stay started when you let off the gas Could somebody tell me what could possibly be the problem? Thank you
    • By RDALE352
      My Rancher cranks right up and runs great for a while and then it will suddenly sputter out and die. It usually cranks right back up and again runs great for a while and then same thing. Yesterday it got to where it acted like it wasn't going to crank back up a few time but eventually did. Any suggestions??
    • By Wesley Floyd
      Hey guys, Thanks for looking at my post. I haven't had a lot of experience with problems like this before, so I'm a little bit at a loss. The Quad was really hard to shift, (the dirty carb leaking gas making it idle high didn't help either). The only Idea I have would be is that the torsion spring is worn out, and that there is a normal parameter for how much it should move when those two arms of the shift shaft assembly spread apart.  That's my thought. Maybe someone who has more knowledge then me can let me know if i'm on the right track 😀

    • By pokerl0w
      this bike! did this guy sucker me or what.. ok, looks like this means something is bent that I do not see or one rod is longer vs the other?
      how long do you think this would last before it ripped into the tire? this is the right side, left side tire clears no problem

       
       
      I can not find them on www.kawasakipartshouse.com
       
    • By johncb
      My brothers 06 outlander max 400 shifter lever is very hard to get into the correct gear any ideas what the problem could be?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...