Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
Admin

Linhai 300 ATV Parts Manual

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By MarkinAR
      So just as a general FYI, it might be good to check replacement parts before installing.  If possible, check clearances with a micrometer before going through the trouble of assembly.  I say this as I bought a new driveshaft yoke for a Kodiak because the ujoint dropped a cap and got the yoke in a bind...blowing the yoke and middle drive gear to shreds.  So I replaced the middle drive gear and bought a new yoke and ujoint kit from Caltric.  Caltric is usually pretty solid replacement parts.  The new yoke however was a good 4mm too narrow for inside lock ujoint caps.  Disappointing since it came as a kit from Caltric.
      Ended up taking an angle grinder to the new yoke and thinning material off to get it to the needed 41.25mm opening size.  Sucks having to disassemble everything again and start over but my fault for trusting replacement parts.  Nearly 40 years of turning wrenches and I made a rookie mistake.
    • By colin james
      View File 2017-2019 sportsman 450/570 with eps factory service manual
      This  is the factory service manual for the 2017-2019 factory service manual for the sportsman 450/570 with electronic power steering 
       
      Submitter colin james Submitted 09/06/2018 Category Polaris ATV  
    • By HeWasRidinDirty
      Anyone know where I can get a free download? I had one a month or so ago on my 'puter but one day it flipped out and I lost it. I gotta put the top end of this 450 together (hopefully today) and I need some info. I've searched and searched this morning, but, I can't find one. Thanks! 
    • By Randel1
      I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.   
    • By bradleyheathhays
      Damn, it took 30 years of driving to cause my first accident, and on Friday the damn 13th. Did a low speed rear end into the back of a lifted truck and got into it's trailer receiver. The only place it made contact with was at the very front center of the hood close to where it latches. Unfortunately the impact was enough that there's a longitudinal hump in the middle of the hood now, bowed 6 inches on each side above the quarter panels, which weren't involved at all thank God. Both my headlights are cracked at the top, but not because they got hit; I think it was because the hood and it's latch was pushed back during the collision possibly deforming the support structure, causing the to separate. The hood is lifted up about 3 inches above each headlight and when looking in at the support material just behind each headlight, one side shows cracks and the other cracks and about a 1/2 gap in the material. Can't tell but it may resemble fiberglass, not really sure? My best guess is that the whole front bumper is gonna have to come off and that entire front support piece be replaced. Any advice on how hard this can be? I do a lot of my own work but I really don't want to be getting into this especially with the weather getting so bad now.


      When I go junkyard shopping for parts, what year Tauruses are compatible with my '02?
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...