Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dwight Williams
Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00. It's been sitting outside with no carburetor on it for about a year. Its rusty, missing some parts, wiring is all cut up and spliced etc. No seat, no racks but the plastic is all there minus the headlight housing. Anyway, who can pass up a $40.00 quad right? I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water. I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine. I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark. Did a quick compression test, 70 lbs. Wet test bumped it up to 90. Ok, so rings and cylinder washed out with water for a year, not too surprised. I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show it's got life. Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either. The compression is now around 60.
Anyway, my question is....is it worth it to try to get this thing going? I tore the top end down today and the cam and one of the rockers is pretty worn. I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well. Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again. Much less just to make it run and use as-is but I won't really like it until it's right. I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much. I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down? I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
I'll get some pictures today if anyone want to see them.
By Dra O
I likely just kissed $200 goodbye buying a Honda 250 this AM from Craiglist. We'll see.
- VIN number is off the front frame; one VIN site calls it a 2008 Honda 250 TRX - this baby ain't a 2008; other VIN sites list the VIN as invalid; might be that the owner (a shady dude from a shadier side of my home town) put a 2008 front end on it? No idea.
- a HUGE hint (hint #1) would've been that there's no key to start the machine - gotta use a screwdriver. I'll likely be visited by police sometime in the near future.
- owner acquired from another man - owner showed me video of him riding it this summer on a major interstate while very drunk (hint #2) - the machine sounded good in the video
- no front headlight; owner said machine has new carb - looks Chinese - he didn't have original carb; air intake box is wide open - no long plastic connection sleeve leading into air box like on my 99 king quad; no visible oil leaks; oil is dark; air filter clean; decent plastic; no front right brake apparatus; left brake handle very loose and rear brake doesn't work
- battery at this point is good; manipulate the ignition switch w/ screw driver and the green neutral light shines (this has since stopped working)
- it's a kick start machine: when I kicked it down (hint #3), the compression sounded normal, almost "tight" but at the end of the cycle, there was some awful grinding noise coming from what sounded like either inside the engine or the starter area; I let it settle, kicked it again, same noise heard at the end of cycle; owner said it likely needs a new starter - I only hope it's this simple
pictures attached - the throttle cable / zip tie pic is my favorite - but it works! it was CRAZY dirty prior to pressure washing - and the water in air box is likely secondary to the power wash - no water was in it when purchased
gotta few things to complete on the king quad - will be changing motor/gear oil in honda and getting new oil filter over time - talk soon - hope y'all had a great Christmas
I have a 425 Magnum that idles great but seems to flood out when I rev it up, sputters, backfires a little somtimes. No water in gas, good fuel filter, carb seems to be fine, good working diaphram. Plug change makes no difference whatsoever.
By jake Stillman
Hello I am new to this forum and lt80s I have an 87 that has burned up 3 coil/cdi combos my question is can I out the newer set up on it and if so how do I do it I know they have different number of wires going to the cdi mine only has 2 please help
Similar Tagged Content
My daughter is a Navy Lieutenant (Captain in the other services). She served an 8 month carrier tour in the Persain Gulf last year. She was the Intelligence Officer for an F/A-18 Super Hornet squadron.
She is currently stationed in San Deigo in another unit. She was recently put on notice she might be picked for a year long assignment in Iraq.
Of course I understand you go where the military tells you to go, but as a Dad I did not want her over there. The Good News is - she is not going. Yeah!
I am indeed a happy Dad.
Recently Browsing 0 members
No registered users viewing this page.