Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Richard Fernandez

2002 Kawasaki Prairie 650 vtwin Bolts to plastic air housing over carbs

Recommended Posts

Just bought Kawasaki Prairie 650 vtwin 2002 and replaced old carb with new, but the bolts to hold down the air housing are missing. Anyone have any idea what size they are? I apologize for not being very mechanically inclined. Any help would be much appreciated. 

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Buell
      Hey guys, figure you guys would have some helpful direction or answers.
      So, 05 Sportsman 700 carb, new carb, fuel pump, new plugs, new air filter, new everything I can think of that is usually the running issues. Starts up fine, seems to run fine, but if under load, two people, or even one person, up a hill, or pulling a drag chain for the driveway, it starts to cut out and sputters and loses all power, until I back off on the throttle and just barely try to let itself catch itself and then I can take off again.
      I am going crazy trying to figure this thing out. Other than that, the quad runs great. Parents bought bran new, just used around the property, 5000 miles on it. Any ideas???
    • By Joe Dickerson
      I decided to replace the rings and piston on this machine because it looked like the plug was being fouled by oil. When I removed the right side of engine to inspect the clutch pack, I found 2 small round pieces with tiny expansion rings in the bottom cover. It looks like "clutch pawls" according to the illustration, but Id like to be sure. I saw that there are 4 of these in the new gasket set.
      Can someone help me here?
      I thank you in advance
      Joe
       
       

    • By matthew smith
      I have a honda recon 250 that i just bought. the compression is around 90 needs to be rebuilt. im getting into rebuilding it took apart the top end no problem except for the cylinder walls. as shown in the pictures. the way the piston sits in the cylinder is if you were sitting on the wheeler the skirt on the piston is left to right. so the wrist pin is front to back. which is where the two marks are in the cylinder. so that means the connecting rod is making the piston slap the cylinder on the wrist pin side which seems like a weird way for the cylinder to be moving. not natural. now the connecting rod has slight play left to right but not up and down. ive talked to a few people they say it might be the roller bearings in the connecting rod where it meets the crankshaft. but the play it has is not that much. im just looking for some more input before i start splitting the case. 




    • By MarkinAR
      And the new 300FW is already wounded. Something got in a bind and blew the whole chunk of case out around the primary drive gear at the back of the motor. In the pic you can see the crack along the top...there is a big chunk missing from the bottom. And it won't roll....but the front and rear diffs both seem fine. Unfortunate. This looks to be a bit of a project. Still feels like it will shift through gears so i'm wondering if the ring and pinion just jumped a bit and blew something to pieces.  I have a parts bike.  But will this require the case to be split and transmission completely disassembled?  I assume you can't just slide the broken primary drive out and slide the replacement in?
       

  • Similar Tagged Content

    • By Jim Waters
      hi everyone. recently iam get a good vibration that comes and goes while iam riding my praire 4x4. iam afraid something is going to detonate. vibration is felt in the steering and then you will here a noise and this comes and goes. its very noticeable when iam on a blacktop surface. iam worried. i cant get any slop in the drive joints i can grab onto. so any input would be appreciated. i have a manual downloaded and i,ve went through it pretty good. my thought is its from the output shaft to the front drive. let me know if anyone has experianced this.
    • By Sonders
      It appears that the Service Manual thread at top of forum is dead as all the links no longer work.  I'm actually looking for service manual for a 2000 KVF300 Prairie that I just picked up.  Does anybody have link to one that they can share, or know where I can find one?  Thanks in advance for any help.
    • By Spartacus Stroppel
      View File 1999-2002 Kawasaki KVF300 Prairie Service Manual
      1999-2002 Kawasaki KVF300 Prairie Service & Repair Manual
      Submitter Spartacus Stroppel Submitted 08/25/2019 Category Kawasaki ATV  
    • By Spartacus Stroppel
      1999-2002 Kawasaki KVF300 Prairie Service & Repair Manual
    • By Wrye Pipeworks
      Picked up a 2000 prairie 300 4x4. It is leaking out of the rear output seal where the driveshaft contacts to the engine. I'm havi g a really hard time finding out how to remove the driveshaft online, finding a service manual, and finding the seal on a parts diagram. Anyone know how to remove the driveshaft or know where a service manual is for it?
      Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...