Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
StolenATV

STOLEN ATV: 2007 Suzuki LTZ 400 Stolen in Tucson Arizona

Recommended Posts

ATV was stolen out of our 2016 Voltage 3305 Toy Hauler that was at Cutting Edge Collision for repairs. The rear locks were broken on the rear of the toy hauler and the ATV was Stolen. Cutting Edge Collision is in a gated and secured area

The post 2007 Suzuki LTZ 400 Stolen in Tucson Arizona appeared first on Stolen 911.

View the full article

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By caperwing
      The rear brakes on this are hydraulic and manual. The hydraulic part is all messed up so I disconnected it all and want to go just manual on the rear. I got it all put back together but doesn't seem to work to well, like not enough pressure. The manual says I should mark the casing before taking it apart which I didn't read until to late. Any ideas? I put new brake pads on.
    • By StolenATV
      This is the information I have on my kids other fourwheeler I dont have a pic of it because I had just got it for them. Just have a pic of the vin plate.
      The post 100CC ASIAN QUAD Stolen appeared first on Stolen 911.
      View the full article
    • By StolenATV
      I went to work at 10:30 am and my mother came out of my house at 12 noon and they were gone. One is a 100cc Chinese Atv I bought for my kids the other is a Yamaha raptor 50 that I got for doing work for a lady for my kids. One picture is the vin number of the Chinese Atv. I will have to go get the title for the Yamaha to get its vin for on here.
      The post My kids 2 four wheelers were stolen appeared first on Stolen 911.
      View the full article
    • By Ajmboy
      Tonight is the first presidential debate and it should be a record breaker for viewing. Might as well have a mini poll here on QUADCRAZY to see how they stack up. Make your choice in the poll and feel free to comment in this topic. I'm going to pin this topic and keep it going through the elections in November. 
    • By Jeff011366
      Hello,
        Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
       
        My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires....  Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
        It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
       
      Thank you in advance for sharing your knowledge.
      Jeff
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...