Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

MarkinAR

1997 Kawasaki Bayou 220 Rehab - wiring question

Recommended Posts

Let me start with I have about 30 years of ATC experience, but not much with stuff made after 1988.  Some, but I'm mechanically inclined so it's all good.  I"m rehabbing a 1997 Bayou 220 to send back into the wild and the mechanicals are now all good, just working on making the electrical system...electric.  Right now, I have no power on the white wire as tested directly on the plug at the starter solenoid.  I'm assuming that wire is supposed to be hot any time it's attached to a battery?  The genius that had it before snipped a couple wires and inserted a fairly heavy push button for electric start bypassing the electrical system. I think i've corrected everything north of the solenoid but the white wire has me stumped.  Is my assumption that this should always be hot with a hot battery correct?  Does this indicate a broken circuit in the starter solenoid?  Relay was also bad and wired incorrectly, but that's resolved and I can make the relay click bypassing the solenoid and connector, directly giving the white wire 12V.  Thoughts?

Share this post


Link to post
Share on other sites


There is a neutral safety switch located on the shifter side of the engine.   It’s a light green and a red wire going into the engine.  

Take the light green wire from the harness side  and ground it. That should close your stayer relay circuit.  If so then you have an issue with the neutral safety switch.  

Share this post


Link to post
Share on other sites

Neutral safety switch grounds normally, breaks ground in gear so it's fine. My issue here is no electricity in the harness at all past the + terminal of the solenoid. For that matter, I get no internal connectivity between + solenoid and white wire spade on the solenoid using multimeter.  I assumed there would be connectivity there within the solenoid circuit even in the absence of electricity.  am i wrong?

Share this post


Link to post
Share on other sites

Yes you should have power on that white wire all the time.    From the positive terminal to the relay, at the relay it branches off internally  into a small fuse holster that’s attached to the relay with a rubber cap over it.

Have you located that’s and checked it? It could also be broken inside the relay.  

You can put a jumper from the positive terminal to that wire to test it your distribution of power to the controls but have a jumper with an in-line fuse just in case you or someone else made a wiring error down the line someplace.  

If you have checked the fuse and still no power then chances are the relay is broke.  

Share this post


Link to post
Share on other sites

Thanks for the info brother. Pretty certain the solenoid circuit has an internal break somewhere. New one should be in tomorrow so we'll find out. Oddly noticed last night that if jumping 12V to the white wire manually the starter engaged. Pretty much tells me the solenoid is bad and stuck closed I think. 

Share this post


Link to post
Share on other sites


Here’s the wiring diagram.   

Mean time take a tester, put it in continuity and go across the two lugs on the solenoid.  You should not get any reading. If so then yes it’s stuck in the closed position.  

Print this diagram out and do what I do, take a few different color highlighters and color code the wires. It makes it way easier to pick things apart. 

 

EF568088-8CFE-4709-8E8E-70B28E4220C7.jpeg

FD1E39EF-0F1D-4E29-A5E8-46D4825929F4.png

Share this post


Link to post
Share on other sites

I had the same problem, ended up replacing a blown fuse and the ign. switch

 

Share this post


Link to post
Share on other sites

To resolve this thread:  it ended up being the solenoid.  The solenoid itself was good but there was an internal break in the circuit somewhere between the incoming 12V from the battery lead and the white wire that should be outbound 12V to the bike.  I did a continuity test on the new one and as expected, there is continuity in a good solenoid.

Thank you all for the help.

Now to just narrow down a few floating grounds to make the dash lights and headlights perk back up and this thing is ready for a new home.

Just started a 1993 Kokiak 400 4X4 rehab as well.  Should be a fun one!

Share this post


Link to post
Share on other sites

Awesome work brother. Let us know how you make out on the bayou. 

Post some pics of the Kodiak ! 

Lets get started on that one.  

Share this post


Link to post
Share on other sites

This is the front birds nest I sorted out. Also attached is the before. Under the plastic was a complete mess but its almost sorted now. Tearing into it revealed a mess but its mechanically ok. Runs good, needs a bit more fuel at WOT. 

IMG_20190809_222835_125.jpg

IMG_20190803_224252_621.jpg

Here is the Kodiak. My oldest picked it up for $600 and it just needs front wheel bearings and the trans case leaks. Small things. Only 1300 original miles. 

20190808_212517.jpg

  • Like 1

Share this post


Link to post
Share on other sites


Two wires were broken inside of the harness and I had to disassemble the combo switch to rebuild the light section (spring was broke in the contact pad...BTW a pen spring is the same size!) and now we're all good. Need to wrap and loom some wires but it's ready for a new home. 

Share this post


Link to post
Share on other sites

Ole 220 drove away to it's new home today. Sold it in an hour, quicker than I thought. Older lady bought it to run out to her deer stand. Good to hear itll be used. 

20190816_085804.jpg

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Steve Howard
      Ran find shut down the quad next day would start and idle when you try to accelerate it would start popping through the carb got a rebuild kit soaked it in chem clean after break down for 12 hours on slow vibrate reassembled and adjusted per manual still the same thing any help would be really appreciated thanks and happy ridding  
    • By mike costa
      Motor starts right up, but when I open it up past quarter throttle it bogs way down while ridding, the longer it runs the worse it gets. If I just leave it in neutral and  give it full throttle it revs up and down. 
      Back history:
      Bike sat for 3 years,
      Installed new plug, cleaned the fuel tank, took it to a shop and had the carburetor gone though.
      Picked up from shop, motor bogged down first day and barely got me back to the truck an 1 mph.
      Took back to shop after a month I was told it had a bad plug, I told him I just replaced it.
      Got quad home and it is doing the same thing!!!!!!!!! 
       
      Thanks in advance for your support!
       
      The carburetor has recently been gone through by a shop
    • By gouletp
      The thing sat since Christmas 2018 and while I decided whether to replace the starter (which I finally did today).  I am not sure if I added fuel stabilizer or not but chances are good I did.  I kept the one year-old battery well charged during the winter.  It turns over well but won't start.  I have a blue spark on a brand new plug.  When I pour a bit of fuel down the cylinder, the engine starts and runs for a few seconds (once for as long as about 8 sections) and then dies.  Even before adding fuel to the cylinder I noticed that the spark plug was wet with fuel.
      The air filter looks a bit dirty so I removed it just to see if the engine would start better but it made no difference.
      If the fuel did not contain stabilizer then the carb may be gummed up.  I don't really want to remove the carb to do a thorough cleaning.  Is there a product I can spray into the carb while the engine turns over that will clean the carb?
      Any other suggestions?
      Thank you
    • By Jeff Comstock
      Help a brother four legger out
       Bayou300 acts like it's flooding if it's it's in the Alabama sun all day but, I've cleaned the carb. Sometimes it'll backfire even though the timing and valve lash are in spec. Thought it was sticking float but after 2 times cleaning the carb I'm lost. So
    • By Slifer
      I have a Kawasaki Bayou 300.  When the four wheeler is idling it won't rev up and the spark plug fouls easy.  It acts like it has a rev limiter.  When I start it, it only runs about 5 minutes and then dies.  Anybody have any suggestions on what might be wrong with it and what it would take to fix this.

  • Similar Tagged Content

    • By Hayden Pahnke
      Bought brand new petcock and carbetator, turned air fuel needle out 2 turns and machine still acts like its starving 4 fuel on top end. Any ideas?
    • By lizalee
      i bought a kwasaki bayou 220 and the person i got it from lost the key so they wired it to bypass the key start to use the pull rope but the wires got unhooked some how now i dont have a clue how to wire it back up to pull rope start. does any1 have a pic of the wires or help me im a newby
    • By Monika Novakov
      1988 Kawasaki 220 Bayou trying to remove generator/ starter 1way clutch cover to be able to replace 1way clutch. All bolts are removed case cover is dripping what oil that remains...but I can't get the cover to come off..what am I missing? Thx in advance.
    • By frostyflammable
      Hello all, wanted to sign up for this site as I am sure I will have lots of questions soon. One of my coworkers has given me a free Bayou 220 that does not run, I was told it needs a new wiring harness, however I cannot confirm any of that yet.

      Next weekend I am going to drive up to the place and pick it up and get some hands on but right now trying to find some service manuals so that I can trace and find out what is going on. My plan is if I can get it to run to do a full restoration and use it to putt around the trails around my house.

      I have some experience with small engines, currently have six mini bikes and a buggy with a GY6 motor that I brought back to life and I am hoping I can do that same with this. Really hoping the Bayou has good compression and it's only a electrical problem.

      In the mean time I am going to be reading this forum to learn as much as I can and hopefully find a service manual. I have attached the only pic I have of it so far.

      Thanks!
      Daniel

    • By 220Bayou
      What weight gear oil for this machine?
      80w90?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...