Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Stacy Hanks

2000 Yamaha Bear Tracker 250 neutral light and ignition not working

Recommended Posts

I have  2000 Yamaha bear tracker 250 - igniton relay and starter relay both were replaced also the neutral switch indicator was replaced-- bike will not show light on for neutral or start when button is pushed

 

Share this post


Link to post
Share on other sites


Are there any lights that come on? sometimes the neutral safety switch can be misaligned. Playing with the shifter, does the light come on at all? can you start the atv with the brakes depressed?

* Edited long topic title and added full ATV info

Share this post


Link to post
Share on other sites

Have you taken a tester or a test light and check for power at the relay ? Not the larger red wires.   There is a smaller plug on the relay as well as a fuse. I’m sure you checked the fuse but have you checked for power on the smaller wires ? We just had a member with a bad relay that had no power coming into the fuse.  

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Bruce Sawyer
      1987 YFM350FWTB 350 4x4 Big Bear when going uphill will sometimes act like the clutch realeases then re-engauge all at once.
      Seems to maybe be little more often if the engine is at about 1/2 throttle instead of at lower rpms.
      I have the Factory Service manual and checked the external clutch adjustment screw as ok and the H/L/reverse shifter lever linkage as adjusted correctly. It appears to be maybe a internal (inside the case) clutch issue or ??
      This is the type Big Bear that has the manual shift lever on the left front fender and has the manual foot shifter lever with 5 speeds forward.
      Can someone tell me how the primary and secondary clutch operates? 
      I assume one is mechanical and one is centrifugal. (what I'm asking is one clutch for the higher rpms and one for the lower rpms or ???. (the clutch appears to only momentarily release at the higher rpms is why I ask. The cycle has about 3000 miles of low speed through the brush hunting and has been well maintained, oil changed, etc and no deep water or mud useage.
      Anyone been into a similar issue with the big Bear ATV????
    • By bodon
      I have a 2011 850 Sportsman.  Has been absolutely trouble free except for 1 thing. I am on my 4th. ignition switch. I don't know if it's that they are all chinese junk or what.  It gets to a point  when you turn the key and it will act like the battery is going bad. Cranks real slow or not at all. Put a new switch in and its fine. New one will last 1 1/2 - 2 years and its junk. I've had the Polaris brand and after market. As a matter of fact the original one lasted the lest amount of time.  Other than that it's been a perfect machine . No electrical problems. No battery problems. Just curious if anyone else has had the same issue.
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
    • By David Miller
      Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks
    • By Colin Davis
      Does anybody know where I can buy a complete wiring harness for a Yamaha bear tracker. If not could someone send me a picture of the the colors of the wires coming out of the cdi plug and voltage rectifier. So I can get an idea of how I need to wire it. Also where can I find a wiring diagram for them?
  • Similar Tagged Content

    • By Bronson Weddle
      I have a 1999 250 Yamaha bear tracker was told it needed a coil to run got into it to day found out that the kill switch was wired together then I found were they put a new cdi on it they cut all the plugs off the stator wires and the cdi wires I found bits and pieces of wireing diagrams blue pick up wire to red and white green wire to white and green wire rolled it over Had a test light on the coil wire it showed there was juice going to it but no spark on the plug and the coil is a brand new one put it on before trying to test the spark did I miss something or have something hooked up wrong already have plans on a new cdi and stator and pick up coil before I go that far like to hear it run. Thank you for the help in advance 
    • By Jeremy Murray
      My 300 king quad will crank and crank off the start button but will not start but you can pull the pull rope a few times and it will start help me
    • By Ben Lennon
      Hi guys new to this forum and thought I’d jump on as I’ve just bought my first quad a Kawasaki bayou klf300c 89 model. It had starting issues when I bought it so I’ve gone thru and replaced the cdi, voltage regulator and starter solenoid aswell as rebuilt the starter motor after all this it was still free spinning on electric start so I pulled the stator cover off to find the fly wheel wasn’t spinning so replaced the one way clutch bearing put it all back together and still not engaging at all. I’m at a loss and looking for some ideas on we’re to look next to solve the problem
      cheers Ben 👍
    • By Brian Simmons
      I put on a new stater  , How would my Yamaha raptor 350 act if the starter clutch went out ??? Please help !!! There is no metal in oil . Its like when you hit the starter button nothing ? Any ideas ???
       
    • By Kristpj
      I know this tooic has been addressed by many, I’ve looked through many forums and pages. I did not find anything like the problem i have.
      I have a 2007 Kingquad 450. I have a new fully charged battery. When i turn the key, the dash flashes and seems to struggle before getting fully lite. We can hear a small relay near the computer clicking, i think it is the fuel pump relay. When i turn off the engine kill switch and press the starting button relays click and all the power shuts off, i turn the key off, engine kill switch then start over, power is there. Atv will start with pull start, but not elextricly. if i try to use my winch, all power cuts and engine dies. 
       
      Can anyone tell me what it may be? or has anyone fsced an issue like this before?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...