Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Jonathan Foster

Honda 185s parts and specs

Recommended Posts

I have a 185 ATC that I’m in the process of rebuilding. Do you guys know anywhere I can find parts or motor specs. I need stuff like shifter seal, head gasket, rings, shocks, and front brakes 

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Randel1
      I am trying to put a 1994 Suzuki 250 quadrunner back into service. I have it up and running like new but need to replace the plastics as they are brittle and crumbling due to age and sun exposure. I would like to purchase new parts either OEM or aftermarket but have had little luck in finding them. I would even consider used or salvaged parts in serviceable condition. Any help in locating these parts would be greatly appreciated. Thanks in advance.
    • By MarkinAR
      So just as a general FYI, it might be good to check replacement parts before installing.  If possible, check clearances with a micrometer before going through the trouble of assembly.  I say this as I bought a new driveshaft yoke for a Kodiak because the ujoint dropped a cap and got the yoke in a bind...blowing the yoke and middle drive gear to shreds.  So I replaced the middle drive gear and bought a new yoke and ujoint kit from Caltric.  Caltric is usually pretty solid replacement parts.  The new yoke however was a good 4mm too narrow for inside lock ujoint caps.  Disappointing since it came as a kit from Caltric.
      Ended up taking an angle grinder to the new yoke and thinning material off to get it to the needed 41.25mm opening size.  Sucks having to disassemble everything again and start over but my fault for trusting replacement parts.  Nearly 40 years of turning wrenches and I made a rookie mistake.
    • By bradley nelson
      Im cool with the police in my area so i can ride on public roads.
    • By Randel1
      I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.   
    • By Jeremy Morris
      If you're getting that pesky leaky seal on the pinion of your front differential and the pinion has allot of play, polaris won't sell the bushing needed to repair it properly without having to shell out big bucks for the complete ring and pinion kit. 
      I have a kit with an upgraded bushing, Japanese made bearing and USmade seal
      50 shipped in the US and 55 to Canada

  • Similar Tagged Content

    • By shaggy051385
      ok guys i have a little problem with my 185s i have tried beating and heating the rear brake drum but it just wont come off any ideas am i missing something here? ive got the outter plate off the one with 6 bolts and that slides right off now the problem i have is with the inner plate it has holes in it but i cant see anything holding it on can some one plz help me i like my trike and would hate to get rid of it just cuz i cant fix my little problem
    • By rapid96
      I have got a 185S three wheeler and i was wondering if anybody knew how to take the rear drum off?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...