Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Wolf Studios

Yamaha big bear 350 NON RUNNER

Recommended Posts

Hi guys so I'm looking for any help or advice with a yamaha big bear 350 1997 (i think) it's fairly dirty and just been say for many years, boss says it's a non runner and I've tried and it will not start, ideally would love to do it up and get it running but have been told the engine has gone, cannot find a new engine anywhere. Anything I should check first before just taking the entire thing apart? 

DSC_0142_1.JPG

Share this post


Link to post
Share on other sites


Wow that’s filthy !!!! I would wash it down  as best possible and start checking things out. Make sure there is oil and the fluids are good.

1. See if the engine turns by pull starter or crank. If the engine cranks then that’s a good sign.  Pull the spark plug to make it easier, and spray some WD 40 into the spark plug hole. If it’s  seized up then it’s a problem and the heads going to have to come off at the very least. 

2. Drain the oil and inspect it for metal particles that could be from a blown crank bearing. 

3. Take a compression reading (if possible)

4. Pull the carburetor off and rebuild/clean it and put it back on and see if it will fire up. (But this only applies if the motor turns) 

You can connect a battery and jump it If you want so you can  really crank it over as well. 

If the previous owner said the engine is dead it could be from a blown piston or a main crank bearing or the transmission is blown. So the engine may run but the bike does not move or vice versa.  

 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By StolenATV
      On Wednesday, September 18, our ATV was stolen from in front of our house after the locks were cut. This was around 2-3:15 AM.
      We realize the likelihood of ever finding the four-wheeler again is slim to none, but we had to try and put the word out there. We have put countless hours in to restoring this Banshee. It was more than just a passion project, it also was our investment for a down payment for our future house. We are devastated and beyond heart-broken. If you see any suspicious postings on Facebook Marketplace, Letgo, Craigslist, etc., or have any other information, please contact us or the Prince William County PD.
      *Update* We received a tip last night that it was possibly posted on Facebook Marketplace around 8AM yesterday morning with only pictures of the front and of the back of the ATV. The description only said: PM for more details. This came up in someone’s FB Marketplace feed that has it set for a 50 mile radius from Hartwood, VA. She also has her feed set to automatically translate everything into Spanish, so It could also possibly be posted in Spanish.
      WHAT WAS STOLEN:
      2004 Yamaha Banshee YFZ 350
      White plastics with bright green and pink graphics/stickers
      STOLEN FROM:
      Prince William County, Triangle, Virginia
      $500 REWARD FOR INFORMATION LEADING TO RECOVERY. BONUS FOR CONVICTION.
      The post Stolen From Our Front Porch – 2004 Yamaha Banshee YFZ 350 appeared first on STOLEN 911.
      View the full article
    • By J Printz
      i have a 2004 Yamaha Kodiak 450 and it is losing oil but does not smoke what is it
    • By Chase Cook
      I have a 2001 yamaha yfm350x and it has a brand new top end, new carburetor (stopped the leaking problem and is now getting gas to it), new CDI box, new stator, handlebar switches work, off-and-on switch works, new starter solenoid (works), new neutral relay (works), ordered a new Rectifier on its way, good strong blue spark. Has compression, valves are right. Timings is right and is TDC. When I try to start it it just makes a loud popping noise like its backfiring but it's not because its not running when I push the throttle all the way and when i barly push the throttle it try to start but won't, so I'm trying to figure out what could be the problem not starting now, Getting very fustrated with this thing and put some work and money into it and it's not still not working. This is the only atv I ever had that I can not figure out the problem to get running. Need help please..
    • By Chase Cook
      I have a Yamaha 350 in at once to try to fire up but won't. It's getting gas fire air and it has a lot of compression but still struggles to start check the timing it's top dead center valves are good valves are adjusted everything's working but won't fire I put my hand over the carb suck in gas and it tries to but it makes a lot of black smoke. Also when I put my hand over do you carb and tried to start it there's black black nasty stuff in the gas. So I don't know if it's trying to burn too much or what it is the gas tank clean and it anything to do with the gas it's with it firing. Took the spark plug out and it's pure black. What is dried up black not nasty corroded wet looking. Need help to solve the issue
    • By Colby Calk
      I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
  • Similar Tagged Content

    • By MarkinAR
      Working on my oldest son's buddy's 2000 Big Bear.  He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit.  It starts and idles like a champ, but dies and wants to backfire with any throttle at all.  I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle.  This one has fuel/air screw, low speed jet, mid jet, and main jet.  I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same. 
      Two questions I guess:
      1. Does it sound most likely trash in the off idle circuit?  This one has a few more passages and jets than I'm used to...and a darn diaphragm.
      2. It now really wants to leak at the bowl drain screw.  It doesn't seem to tighten enough to completely stop the flow.  Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper.  First for me.  Any idea here?
    • By Walter Awe
      I HAVE a 2002 big bear 400 4x4. I have two wires atacking to the front of the carb. What are they for?
    • By Shook
      Hi I have a 2000 big bear 400 and i just put a new carburetor on it and it idles fine but when you try to accelerate it sounds like it is going to die, so when it sounds like it is going to die I will give it more throttle then it will go just fine.
    • By Nigel Bourn
      I’ve just bought one of these and came here looking for a service manual
      Mine has an air cleaner that I don’t seem to be able to find, it has round ends with square tabs on them, any ideas?
       
    • By Scott Matthews
      Just picked up a 1989 Big Bear 350 for $250 CAD. Bike was running but lost crank and spark. They've installed a new coil, a couple relays, and installed a Ford starter solenoid in place of the original. Now it cranks but has no spark so they sold it to me. Does anyone have a wiring diagram for this bike so I can test some wiring. Also any ideas as to direction to head would be nice. Lots of things have been hacked together so I know it probably wont be to easy. The ignition switch was replaced with a toggle switch, I already mentioned the Ford solenoid which 1 of the small wires was not re-installed, and a diode or something was removed from the oil temp sensor wire. I'm sure I will find more so a diagram would be amazing.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...