Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Shawn Hurt

2013 Suzuki King Quad 750 tire wear

Recommended Posts

I have a 2013 KQ I bought it new but rolled it a few years ago. I have replaced the left lower A-arm and left tie rod, the steering is still a little sketchy as I just eye balled the alignment. But the major issue is the left front tire cambers out at the top and has wore the tire bald. Tires have about 2000 miles on them but other 3 are half tread and left front is a slick.. I can not see anything else bent and don't know what to do..  

Share this post


Link to post
Share on other sites


Hey @Shawn Hurt welcome to Quadcrazy. When you roll or wreck a quad what’s not really understood is the tubular frame.  It’s not as strong as you would think.  Having said that I don’t think a roll over would bend the frame but would do a little more damage then you would think.  Hear is what I would do. 

Take the machine and sit it on solid level ground like a garage floor with a nice level slab.  Jack the front end up and take the tires off, then pull the shocks off as well so both swing arms are hanging. Double check for any additional damage you may have missed initially. 

Then take some measurements of the bottom of the rotor to the floor and some other measurements along the frame. Maybe from the front push bar to the edge of the rotors etc and look for something that stands out. Could be as simple as a bad shock. Or in need of an alignment, the tie rod ends could be out of whack etc.

Something is going to jump out after taking measurements.  Shit I would even put a laser on a block and see how the front end sits across  the center of the hubs where they bolt up, the main bolt with the cotter pin that holds the hub on. If you put a laser on them they should be pretty level  just make sure you have the bike on somewhat level ground and it’s jacked up level.  Use a torpedo level across the frame and see how it’s sitting, level it off and hit it with a laser level after you know the frame is level.  

If the handle bars got hit then the steering column could have been bent.

Chedk how much thread is exposed on the tie rods and they match each other, if one is more the the other then that’s a problem. 

Most atv’s when they do not have a rider on them sit higher due to the anticipation of additional weight of the rider so they may slope outward slightly when it sits without anyone on it.  When you sit on it the wheels come in due to the weight. So also have someone that’s similar in weight sit on the bike and see what the front tires look like from the front.    

 

 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By John Dunn III
      Just bought a LT 230 anything I should watch for. It runs and drive good. Just don't want no surprises 
    • By turner_clint77
      Just have a couple questions 
      first does anyone else have an issue with the right hand tie rods coming loose 
      second does anyone else’s power steering making a weird sound at times 
    • By Skhot K
      Hello! I picked up a YFM400 and I would love to talk shop with knowledgeable co-owners, and I'd love input about the machine from anyone here who clearly knows more than I do! Cheers from NY
    • By Jeremy Morris
      If you're getting that pesky leaky seal on the pinion of your front differential and the pinion has allot of play, polaris won't sell the bushing needed to repair it properly without having to shell out big bucks for the complete ring and pinion kit. 
      I have a kit with an upgraded bushing, Japanese made bearing and USmade seal
      50 shipped in the US and 55 to Canada

    • By bradleyheathhays
      Damn, it took 30 years of driving to cause my first accident, and on Friday the damn 13th. Did a low speed rear end into the back of a lifted truck and got into it's trailer receiver. The only place it made contact with was at the very front center of the hood close to where it latches. Unfortunately the impact was enough that there's a longitudinal hump in the middle of the hood now, bowed 6 inches on each side above the quarter panels, which weren't involved at all thank God. Both my headlights are cracked at the top, but not because they got hit; I think it was because the hood and it's latch was pushed back during the collision possibly deforming the support structure, causing the to separate. The hood is lifted up about 3 inches above each headlight and when looking in at the support material just behind each headlight, one side shows cracks and the other cracks and about a 1/2 gap in the material. Can't tell but it may resemble fiberglass, not really sure? My best guess is that the whole front bumper is gonna have to come off and that entire front support piece be replaced. Any advice on how hard this can be? I do a lot of my own work but I really don't want to be getting into this especially with the weather getting so bad now.


      When I go junkyard shopping for parts, what year Tauruses are compatible with my '02?
  • Similar Tagged Content

    • By davefrombc
      1987-1998 Suzuki Quad Runner/King Quad 250/300 Service and Repair Manual
       
    • By davefrombc
      View File 1987-1998 Suzuki Quad Runner/King Quad 250/300 Service Manual
      1987-1998 Suzuki Quad Runner/King Quad 250/300 Service and Repair Manual
       
      Submitter davefrombc Submitted 01/28/2017 Category Suzuki ATV  
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By marek porowski
      It’s kind of ATV related question as I need new trailer tires to tow my 4 wheeler. 
      Does anybody have any experience with loadstar 12” trailer tires ? 
      There is not to many choices for trailer tires here in Ontario and I was wandering if somebody can recommend me something. 
    • By DUBLT
      Looking to purchase a windshield for my ATV, suggestions of what to buy with quality in mind and will fit without doing any modifications. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...