Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

mothrottle

US made grease gun fit Metric Zerk fittings?

Recommended Posts

Does a US made grease gun fit Metric zerk fittings, or do I need a conversion to fit them?  Thanks in advance.

Share this post


Link to post
Share on other sites


I think most do, depends on the adapter. You can always replace the adapter with something like:

Gurtech Grease Gun Coupler XL Long Series - Fits All SAE and Metric Zerk fittings

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Gilbey
      What is everyone's choice for differential grease? And does anyone have an idea of capacity for 2007 Sunl (Chinese)250 CC ATV as I do  not have the owners manual with specs. Thanks for the input.
    • By YamahaGrizzly
      Billy went all out and bought N2deep Snorkels, Rubber Down customs Rad kit and Rox speed fx Risers for his Grizzly 700. It took a solid 3 days in the shed to install all this new gear on Billys Yamaha grizzly 700! We cant wait for the next time we get out and go on a run! should be this week actually! gonna be good to get the Yamahas grizzlys and Kodiak together!
    • By killer420
      I know this has been talked about, so i did some research.
      After my research, i started buying parts.
      Here are the parts you need:
      51380-HP7-A00, left front upper control arm
      51370-HP7-A00, right front upper control arm
      51350-HP5-600, right front lower control arm
      51360-HP5-600, left front lower control arm
      44615-HP5-600, front drive hubs (need 2)
      53521-HP5-600, tie rods (need 2, this is just the adjuster rod, not the tie-rod ends)
      51200-HP5-600, right steering knuckle
      51250-HP5-600, left steering knuckle
      53235-HP5-600, steering arm (connects the tie rod ends to the steering shaft)
      23611-HP5-600, "final shaft", goes inside the engine, provides power to front and rear driveshafts)
      40400-HP5-600, front driveshaft
      44250-HP7-A31, right front axle
      44350-HP7-A31, left front axle
      11300-HP5-000, front crankcase cover
      50350-HP5-600, front differential support bracket
      41400-HP5-A50, front differential unit
      You also need the 4wd shift lever and the cable that connects it to the differential. there is not a part number for the whole assembly, just look on ebay. thats where i got mine.
      Now on to the good part, the turning of wrenches:
      Here is the engine before removal:


      after removal:

      front differential in position:

      ^^^notice the "TRX420TM" decal, indicating 2wd
      Here is a pic of the "final shaft", comparing the 2wd (in my hand) to the 4wd (in the engine).

      ^This is the most difficult part of this conversion, removing and opening the engine to swap out this shaft. However, there is a lovely video on youtube showing how to rebuild this engine and they clearly show the steps to remove/replace the rear cover and final shaft. Dont forget to remove the front cover before installing the new shaft, it will not fit thru the 2wd front cover.
      link to video>:
      once the new shaft is installed:

      you will need to install the front and rear covers using sealant, make sure all shims/washers and o-rings are in place in the correct locations referencing the video above.
      here is the right front corner mostly assembled:

      and fully assembled with hub, rotor, and brake caliper:

      I do have more pictures to upload, when i have more time i will update this further
    • By Freedomflyer
      I just bought a 2018 Can Am 570 Outlander and was hoping to try to find a way to convert a Can Am 2-up seat that I picked up on Craigslist  to my new machine in some fashion.  No way to do it without the seat sitting up 8-9 inches above the main seat. Scrapped that Idea but decided to try to convert it to my Honda Rancher.  Also in a way that would allow me to remove it quickly and allow access to my battery compartment if necessary. Here's what I came up with.  
      Since the seat has two fork like protrusions on the front underside I needed to come up with something that they would lock into. On rear underside there is a spring loaded handle that allows it to lock onto a 3/8" round bar.  I wanted the bar that the front part of the seat locked into to also be removable so I came up with a design for the bar that would slide onto the front side of the rear rack and pin into place using the rack itself as the mounting base. Then I welded a couple pieces of 3/4" pipe to the rear part of the rear rack with a piece of 3/8" solid bar stock onto the front of the two pieces of pipe that were welded to the rear section of the rack.  The forks of the seat lock into the front bar, the pipes at the back not only support the rear part of the seat but act as a centering guide for the two locking mechanisms that lock onto the 3/8" bar stock. When it is locked into place it is extremely solid and has no way of coming loose except when I release the spring loaded handle. And it actually doesn't look too bad when installed either. Plus, the front side of the rear seat acts as a back rest for the small of the drivers back, pretty cool.









    • By Stephen Smith
      My grandson has a Falcon 90 and needs a power upgrade. Does anyone know if the 110 motor will bolt into the 90 frame without a bunch of modification?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...