Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
StolenATV

STOLEN ATV: 2003 Yamaha 660 Raptor and 2014 Honda Foreman 500

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By dany desbiens
      Hello i have a Polaris 2003 sportsman 600 Polaris Sportsman OEM Gauge Speedo Speedometer Display Dash Cluster 3280425 the speedo is not working no 4*4 i can find nothing can i put a speedo 2004Speedometer Gauge Speedo
      3280431 04-08 Sportsman if it will work
    • By Arizona
      Well im at it again, took about an hour drive Saturday and made a deal on this old honda. 
      Might be restorable. Tires pretty dry rotted, mastercylinder broken glass and probably full of water. 
      Handed me the carb he rebuilt (oh no) He said ran about 6 months ago but when we pushed out of his
      field there was a tree growning through it. See pic.  Missing some parts, also missing the intake. Motor is not
      locked up, Has piece of plastic crammed in the head since no carb there for months. Brake cables bad, etc. Thats
      part of the fun. Im sure I will be posting some questions later for you all. Stay tuned Az.

    • By Venom
      Hi All,
      I did a total restoration on a 2003 Yamaha Raptor 80. Rebuilt the engine and tranny.. Started it up today and it runs great. Took it for a ride and the transmission worked perfectly. Adjusted the carb a little more and went for another ride. It ran awesome, pulled into the workshop shifted into neutral ( Neutral light came on) and shut off the bike. went to roll it and noticed she would not roll. Turned on the key and neutral light was on... After some troubleshooting I found that she is in first gear with the neutral light on and will not shift into neutral... It seems to up shift fine into 2nd and 3rd and then back down to 1st. I am hoping somebody can shed some light on what is happening... Thanks for any help...

    • By Randel1
      Hello, 
      I have a 2004 Yamaha Bear Tracker in the shop for repair. I have the service manual but it doesn't have all the information I need to fix the problem. I need to know the voltage output of the stator charge coil and pulse or trigger coil at cranking speed. The wiring diagram color code doesn't seem to match and that is compounded by the fact that the wiring harness CDI connector is missing so I have 7 wires that need to be connected to the CDI. I can not find a circuit diagram of the CDI which tells me where the pulse/trigger coil connects or the charge coil connects. The other 3 wires (black ground, orange ignition coil, and r/b ignition kill sw) also need to be connected. The CDI has a single 8 pin connector and has a P/N 4XE-00 F8T19871 -1122 number on it and I believe it to be OEM. However I think the Stator and pulse coil are aftermarket items. I have resistance tested everything and it all seems to be in spec. but I don't want to miss wire anything and cause damage. Any help would be greatly appreciated. 
    • By Venom
      Hi, All

      I started this project a while ago.. I have decided to make one thread I can continuously update..

      So , here we go. I got this Raptor 80 in really bad condition.. Rear end frozen, Engine toast, tires dry rotted, tons of rust..etc.. They admitted they beat on it very hard.

      Since they do not make these with a drive shaft anymore I decided to restore it from top to bottom..

      These are photos of when I got it home.

      Next up, the tear down..



      First, I needed to tear it down and determine if the rear end was still good... As we all know... That is where it would be cost prohibitive to restore if it is trashed..

      Got it completely stripped down and I lucked out... The rear Drum brake was caked solid inside with dried mud. That was causing the rear end to lock up. Took off the rear brakes and the rear end spun perfectly smooth.

      Once I got it all stripped apart I needed to take the finish off all the parts. I am going to be powder coating the frame and many parts.. Once the finish is off each part it will need to be sandblasted to white metal .. The guy I use for powder coating gives me a hefty discount if I bring the parts to him ready to go.

      You could just sand blast, but that would take a long time to get the finish off. First I used Aircraft Paint Remover.. That stuff is pretty toxic Goggles and Resperator are required. That quickly gets you down to the metal... Then you can sand blast to white metal pretty quickly...


      I had another thread I had started about a problem with the tear down... It has some great info .... here is the link... It is about removing the frame bushings. ....
       
      https://www.quadcrazy.com/atvforum/topic/14209-raptor-80-frame-bushings/?tab=comments#comment-104702
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...