Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Scott Sirr

2008 Yamaha Big Bear 400 neutral light not working most of the time.

Recommended Posts

I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.

I think it is in the right side engine cover area, but not certain. 

 Any help would be great. thanks

Scott

Share this post


Link to post
Share on other sites


Most likely  it  is  the same switch located in the same place as in earlier  models.  There  are  Big Bear 400  manuals  in the  download section ..  Check   them  out  for  the placement  of  your  switch .. It  may  be  something as simple  as a  bad ground .

  • Like 1

Share this post


Link to post
Share on other sites

Thanks for your response davefrombc, but it looks like the older switches were on the outside of the engine/transmission but in 2007 there was changes when it went to irs. So I think it got moved and there is no manual that I can find for 2007 or newer?

Edited by Scott Sirr

Share this post


Link to post
Share on other sites

I  haven't found a free download of the    manual  for  the  newer ones ,but there's several  pay  ones available .

 

Share this post


Link to post
Share on other sites

Ya I guess I should just break down and buy one. It would save lots of headaches later :)

I need to make room I the garage to have a warmer place to work on it.

 

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By John Victor
      My father-in-law gave my boy a 1999 350 Big Bear. It's been sitting in a barn for a bunch of years. It runs great! My boy has been riding a couple weeks now and it has developed a squeal coming from the front end when you get off the gas at speed. No noise during acceleration. At first I thought brakes. I took it for a ride and I don't think it is the brakes. I feel it is the front prop shaft U-joints, front differential or one/both axles. I pulled the fill plug on the differential and I can't find anywhere how much gear oil should be in there. My gut says up to the fill opening. It doesn't have a manual. It's wet in there, just don't see any gear oil.

      #1 Should I fill the differential with gear oil up to the fill opening?

      #2 How do I check or know if the u-joints are bad? That looks like a "Big Bear" of a job if they don't need to be replaced.

      #3 What else could it be? I don't think it is the front bearings. I jacked the front wheels off ground and no play in the right wheel. Very little play in the left wheel, looks like the lower control bushing is where that play is coming from. The rubber CV boots look original but all still intact. Wheels spin easily without any noise.

      Thanks for any help!
    • By Erik Plug
      Hi all,
       
      Picked up my first Brute Force yesterday. What should have been an awesome afternoon of riding turn a bit into a deception. As I was unable to really take it out for a test drive at the shop, I decided to buy it and agreed that I would take the test drive at home. 
      When giving full throttle I noticed that the Brute was choking and lost all of its powers. Faulty fuel pump most likely. 
      Called the shop and the are coming to pick it up and repair it and bring it back. Good service. Nevertheless feels a bit sour in the mouth as I was told it was a 100% good. 
      Need to have some patience I now before I can really start riding. 
      Cheers,
      Erik
    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By Ajmboy
      Got my Yamaha Grizzly buttoned up finally and went for a quick 2 hour ride in the power lines with my neighbor, who has a Yamaha Kodiak. We have access from his yard, which is nice. Was a beautiful day today to get out and will try to go more often. Ran into two other quad riders with a sportsman and I think grizzly. Also ran into a dirt bike rider. 😎




       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...