Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

YamahaBB350

Yamaha Big Bear 350 Reverse not Working

Recommended Posts

I have a Yamaha Big Bear 350 and the reverse doesn’t work, it shifts from low to high easily but it won’t go back to reverse. I’m new to this stuff, so I’ll take any help. Any ideas? 

Edited by YamahaBB350
Mistake

Share this post


Link to post
Share on other sites


Does the shifter feel wrong ? Is it shifting into reverse but not moving ? Have you checked the fluids in the gear case ?

lastly try getting all four wheels off the ground and see if the bike goes into reverse.  

Share this post


Link to post
Share on other sites

Wow great point @Ajmboy i remember this topic! Could very well be just that ! 

I think it was the brake cable  adjustment or the linkage.  One or the other, we had another member that made adjustments and was no longer to get in reverse and he put it back where it was and it was fine. Maybe @Arizona

  • Like 1

Share this post


Link to post
Share on other sites


It shifts from low to high while not running but when I try to go to reverse it just is stiff like the cable doesn’t move. Should I lower the idle bar and see if that does it? 

Share this post


Link to post
Share on other sites

On mine I had to loosen up the foot pedal adjustment, I guess it needed to move more.

I adjusted my rear brakes and that's what caused the problem, after loosening them up 

it worked again, Also had to be in 1st in order to go into reverse. Seemed to be a problem

an each Yamaha I have owned. Just got rid of one and same issues. 

  • Like 2

Share this post


Link to post
Share on other sites


Don’t think I can help on this one. Mine was a 03 and automatic. However on that one you had to depress the foot brake to shift to reverse. There was a locking pin on the foot brake linkage. I deleted that to bypass the brake/reverse thing.   

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By Gordon cousins
      I have a 1991 Big Bear 4x4   Shifter on top. Any one know if a  1994 Big Bear 4x4 Shifter on motor can be swapped 
    • By StolenATV
      Taken from my car port around 0330 and was taken by at least 2 people found footprints pushing the quad all the way to the road (80 yards)
      The post 2012 Yamaha Grizzly 700 EFI 4×4 Stolen appeared first on STOLEN 911.
      View the full article
    • By Dwight Williams
      I have a 99 Kodiak 400 4X4 that I picked up for $300.  The previous owner had modified the foot shifter by welding a piece of rebar to it so he could hand shift while plowing.  As you can imagine, the allows for much more torque on the shifter than it was designed to have, and he broke the stopper off of the the shift mechanism.  No big deal, I ordered the part and put it back together, went through the carburetor and off we go, it runs pretty good.  
      The first thing I noticed is that when I put the shifter all the way down it goes into reverse, I'm supposed to twist a knob to get it to reverse but this seems to be disabled.  Also, once in reverse, it's a bugger to get back out.  I have to hold the shifter up, then quickly back down and up again to get it to come out.  All forward gears work fine, clutch is tight, no problems.
      The reverse cable and lever are in tact and seem to move freely.  
      My question is this:  What does one normally have to do to get this thing into reverse?  I assume put it in neutral, twist the knob, kick the shifter down.  Does the brake need to be applied?  I'm not sure what's going on here, I suspect it's been 'modified' as it goes into reverse without the proper precautions, just not sure if the mods were external on internal.
       
      thanks
    • By K L Buck Naff
      Trying to replace the carburetor on my 2003 Bear Tracker 250. Two brand new carbs in a row from different suppliers.   Both leak fuel out over flow and intake as soon as I turn the gas on. Any ideas. Am I doing something wrong?
  • Similar Tagged Content

    • By Aaron Drost
      Hello bought my 2000 polaris sportsman 500 last week bike seems to work pretty good untill yesterday, when in reverse the bike seems to start bogging out? How come? 
    • By Milsparro
      Howdy y'all. Just bought myself a 2004? Yamaha 400 with electrical Gremlins aplenty. Runs good (after jumping the starter solenoid relay terminals with the helpfully included with the sale pliers) but no fan when my wife's 03 Kodiak 400 had fan and the starter button makes it to the starter solenoid but the ECU side isn't happy. This seems to be a lively forum with manual downloads being supported so hi.
      Oh yah, and you can get two Kodiak 400s on a 5x8 trailer... I bought a nice 14' trailer as soon as possible after this.

    • By Nate Hanson
      I am a new atv owner...I bought a used atv this summer (pretty sure it is a wolverine but reg card from last owner didnt actually say that so idk for sure). It ran great for most the summer and early fall but one day I tried starting it and it turned over a while without starting and then suddenly it quit turning over at all. No click or anything.
      I charged battery and light turns on showing neutral and heatlight can go on.
      A few other things that may be pertinent: The pull start is missing, I have a fluke multimeter but not many other advanced tools (or relevant experience), there is an extra aftermarket led light attached to front but it doesnt work either... never looked into why since I didnt need it. 
      I looked for a fuse box and didnt find one.
      Please recommend some easier things to try first as I really want to avoid taking it in if I can (having one income and 4 kids can keep out extra cash, plus I want to learn). Pictures would be awesome if possible. Thanks! 
    • By Kanyon Pershing
      I have recently rebuilt my Yamaha warrior 350 engine and when I got it all back together with no “spare parts” i went to start it and realized it’s in reverse. I went to put it in drive and the shifter won’t budge, I took the linkage off and tried to use vise grips but it won’t budge at all. Any help would be greatly appreciated. I’m hoping it’s not something internal! 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...