Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Guythis448

1988 Honda TRX 300 wiring diagram

Recommended Posts

Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 

If anyone could drop a link or send me a PM it would be much appreciated 

Share this post


Link to post
Share on other sites


Look  in the forum  downloads section. There is  the service manual  for the  '88 - '94   Honda 300's  there

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Gary Patch
      hi have really old Honda 4x4 how do I find out model no  etc as need new starter motor think its 350 cc but not sure thanks in advance
    • By Hondasher
      I have a 2004 Polaris Trail Boss 330 and I want to eventually fix it up if possible, but the thing is the transmission or Gearbox that allows you to shift into forward and reverse and such isn't connect to the engine at all, it isn't even bolted into the frame. Anyways the Secondary Driven clutch is missing. The ignition was busted so I switched it out and tried to hook up power to it and the lights wouldn't light up and it wouldn't try to let me start it with the electric starter. 
       
      So I bridged the connectors on the starter solenoid and it cranks the motor. I was wondering if anyone knew why the dash lights don't work or any of the buttons. I did find a cable disconnected I have a picture of maybe someone can tell me what it's supposed to be connected to. It has 3 wires going to the connect Green Purple Red. I'll enclose a picture of it and where it is connected on the wiring harness. 
       


    • By MarkinAR
      I'm likely going to have to drop the swingarm on a 300FW. Are the lock rings and pivot bolts standard or left handed threads?  I looked at the service manual and it doesn't specify left hand so I"m assuming standard right handed threads.  Not sure though.  The last Yamaha I had apart was regular right handed threads but haven't had a 300 apart before.
    • By Amazon Ads
      Where do you buy your ATV parts? Did you know that Amazon has ATV parts in stock for immediate delivery? You'll find all the best ATV parts and for great prices! Check out all the ATV parts available with free 2 day shipping now...
    • By Andrew Baker
      I need help with wiring on a 1998 (I think, 10th digit of the VIN was W) Bayou. I'm not getting spark, I'm pretty sure it is due to grounds being off because the harness is pretty hacked as far as the electric start and charging system goes. I'm needing a good wiring schematic. I found one online and there are a few things that don't add up on it so I'm skeptical that it is really for my year and model. Any help would be appreciated. Thanks. 
       
  • Similar Tagged Content

    • By thegipper
      Have replaced, Carb, fuel pump, CDI, plug, coil,fuel filter. Will crank but not srt. Getting spark and battery is fully charged 12.6V
      Any suggestions????
       
      Thanks
    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
    • By Trenton
      Hello. I am a new member as of today. I had a quick question to ask. I recently was driving mt HONDA RANCHER 2004 GPSscape 400 and my display stopped working. I was driving the atv and all of a sudden the speedometer and the service lights went out. Also the lights stopped working. I am still able to shift gears, change from 2wd to 4wd, and can still select if I want EPS or Auto. I have checked my fuse box and have changed a few of them around. It did not change anything. I was wondering if anyone had any idea of what had happend. Thank you for your time- Trenton 
    • By wHarmon
      Our 1988 Yamaha Terra Pro is finally seeing the finish line of becoming our new bush hogging tractor! I've had the terra pro for almost 2 years... we had great intentions, but after removing the fenders, fuel tank, and the carb, we let it sit up. Shame on us! However, the terra pro is cranking today. We cleaned the carb, figured out what goes where and where did that screw go! She smokes like there's no tomorrow, but that's okay! The only issue right now is getting all these lines hooked back up to the carb right! There is 5 lines to hook up to this thing!! And in our moment of drinking and removing parts, we cant remember how they go back on. I've found several diagrams online, but none showing the overall schematics of all the lines! If anyone has a service manual, or any way of helping us figure out what goes where I would really appreciate it!! I can attach pictures later if it'll help!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...