Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Ellery Zandt

KAZUMA REDCAT 250CC ATV ANTIFREEZE LINES/ CARB W PICS

Recommended Posts

I have no idea where the antifreeze line coming off the thermostat goes too. The carb two nipples in the pic create a vacumme. Can someone help me on this please....!!! my email direct is [email protected]!!!!82266641_823005951479596_3133860167842529280_n.thumb.jpg.08c977be061e536893076d1cde63c236.jpg174410997_carb1.jpg.cc4f3d2d6bdd5a9f32cb7954f32de32f.jpg

Share this post


Link to post
Share on other sites


Hey @Ellery Zandt welcome to Quadcrazy. FYI you should never post your email here. That line usually goes from the thermostat housing cover to a connection near the water pump. What its designed to do is allow some coolant to circulate through the system when the thermostat is closed. Its like a small bypass.  
I'm not sure on the Kazuma but if you can post a few more pics of the water pump area maybe we can help you out.  

Share this post


Link to post
Share on other sites

As far as the vacuum connections on the carb, they will usually go to a fuel pump thats operating off of the vacuum.   Check the fuel petcock and see if you have two hose connections.   

Share this post


Link to post
Share on other sites

I think the carb is fine then. We just dont have any nipple off the water pump thats where we are confused i will take another look tonight will post another photo

Share this post


Link to post
Share on other sites

Double check the reservoir for any connections, i doubt it bc its a pressurized system but you never know. 
The only other way to check is to put a pump on the  radiator  cap. Put pressure in the system and see where you have coolant coming out.  You will have to block off the port on the thermostat housing with a piece of hose with a bolt in it. They sell a multi pump for all types of radiators at Harbor freight that pressurizes  the system to help find leaks. I am sorry but i am not familiar with the Kazuma brand. 
I looked for the manual but don't see it in the library. 

Share this post


Link to post
Share on other sites


tres.jpg.290580f5058b015698715be0f3948c7d.jpgdos.jpg.724cd528304b90e912074be16cdb747a.jpguno.jpg.e4fdce2bf1d2e47ca5486ffa06a84320.jpg

bloq.jpg

I wonder if you just cap it will it matter honestly. I really dont know. Looks like it would get enough flow from the main radiator line

Share this post


Link to post
Share on other sites

Im pretty sure it would but it belongs someplace and that really should be figured out.  
I will keep looking, if i find anything out i will let you know.   

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
    • By Ellery Zandt
      Does anyone have a redcat 250 or falcon 250cc that they can share where the two vacuum lines on the carburetor that you run antifreeze through I honestly have no idea where the lines are suppose to go to circulate the antifreeze. 
       
      Any help is greatly appreciated. 
       
    • By Jim Denton
      The Shindy kit has been recommended as well as the random chinese kits. My last couple of Harley evos were c/v carbed. They both have been treated to a similar mod kit as seen below the better throttle response was nice and they breathed better. Has anyone tried this kit? I'm itching to start my project and will have to do a carb regardless. The H's also got new Andrews Ev-27 cams



    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By jimsvtx
      I'm working on my brothers' 2002 Suzuki Vinson 500 . It sat for a few years before I got into it. I'm concentrating on the carb - I replaced orings, needle, etc. and soaked jets, bowl and anything that I could get off the carb that the solution wouldn't eat. I also removed the tank and flushed it with hot water - it's clean. The gas cap innards rusted away and the tank had a lot of rust and water in it before I cleaned it. I replaced the gas cap and installed a new fuel valve because the screens were broken in the old one. The bike will run but spits and sputters and backfires. If you "open it up" it falls on its face and stalls - but starts right up. Here is a link to an exploded view of the carb: Ohio Honda Yamaha Motorcycle ATV Dealer - J & J Motors - Kawasaki Suzuki Scooter Utility vehicle, parts, accessories, apparel
      Can anyone point me in the direction of the problem? It may still be a "clean carb parts issue" . My problem is that the parts list doesn't identify the parts to a degree that I understand. If you said" look at the pilot jet", I'm not sure which jet that would be....See what I mean? It'll run very good if I remove the air filter and cover the opening with my hand and part my fingers a little for the air to get in. Any help is greatly appreciated.
      Thanks in advance, Jim
  • Similar Tagged Content

    • By Ellery Zandt
      Does anyone have a redcat 250 or falcon 250cc that they can share where the two vacuum lines on the carburetor that you run antifreeze through I honestly have no idea where the lines are suppose to go to circulate the antifreeze. 
       
      Any help is greatly appreciated. 
       
    • By Ajmboy
      View File Kazuma and Other Brands ATV110-M Service Manual
      This is a supplemental service manual for Kazuma and Other Chines brands 110 ATVs.  ATV110-M Service Manual
      Submitter Ajmboy Submitted 10/21/2019 Category Kazuma ATV  
    • By Ajmboy
      This is a supplemental service manual for Kazuma and Other Chines brands 110 ATVs.  ATV110-M Service Manual
    • By Paul Maple
      I have a 1999 Sportsman  500, it was running fine, than started to lose power in the winter, I adjusted the idle screw and away I went, than a few weeks ago it died, I have found that i am flooding the engine, compression was at 70PSI and due to the compression release mech. i assume i am good as it compared to the same PSI on a 2000 sportsman 500 i have. i cannot start the atv unless i go full throttle and it starts an runs for about 30 sec than dies, again it is flooded. i ordered a new carb off ebay as i could get one for around $40. put that in same issue, i have checked the timing, (good), valves out of adjustment i adjusted to .006 still same issue, i have found the exhaust lobe and rocker arm to have some wear, i have ordered new ones, but am looking for any other input in this area as well. would the exhaust cam and rocker arm cause the engine to flood? i have used a bore scope and the piston liner has good cross hatching still? any input would be great.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...