Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

MarkinAR

General FYI on replacement parts

Recommended Posts

So just as a general FYI, it might be good to check replacement parts before installing.  If possible, check clearances with a micrometer before going through the trouble of assembly.  I say this as I bought a new driveshaft yoke for a Kodiak because the ujoint dropped a cap and got the yoke in a bind...blowing the yoke and middle drive gear to shreds.  So I replaced the middle drive gear and bought a new yoke and ujoint kit from Caltric.  Caltric is usually pretty solid replacement parts.  The new yoke however was a good 4mm too narrow for inside lock ujoint caps.  Disappointing since it came as a kit from Caltric.

Ended up taking an angle grinder to the new yoke and thinning material off to get it to the needed 41.25mm opening size.  Sucks having to disassemble everything again and start over but my fault for trusting replacement parts.  Nearly 40 years of turning wrenches and I made a rookie mistake. :)

  • Like 1

Share this post


Link to post
Share on other sites


Oh that happened to me on my 800.  I thought I blew a belt, but the rear drive shaft had blown up and dropped out of the atv lol. Heres a pic. Cost 80 for a new shaft works good now.  I had noticed that the old drive shaft appeared to be to short as it only reached half way up the rear splines

20191225_121948.jpg

  • Like 1

Share this post


Link to post
Share on other sites


I did but haven't seen a reply yet. Probably a result of outsourced parts from overseas. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By mothrottle
      The VIN on my 2018 Kodiak 450 is not where it's supposed to be. I bought this used. Is there another "hidden" location where I can find it? Need the number for insurance co. Thanks in advance.
    • By David Miller
      Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Dwight Williams
      I have a 99 Kodiak 400 4X4 that I picked up for $300.  The previous owner had modified the foot shifter by welding a piece of rebar to it so he could hand shift while plowing.  As you can imagine, the allows for much more torque on the shifter than it was designed to have, and he broke the stopper off of the the shift mechanism.  No big deal, I ordered the part and put it back together, went through the carburetor and off we go, it runs pretty good.  
      The first thing I noticed is that when I put the shifter all the way down it goes into reverse, I'm supposed to twist a knob to get it to reverse but this seems to be disabled.  Also, once in reverse, it's a bugger to get back out.  I have to hold the shifter up, then quickly back down and up again to get it to come out.  All forward gears work fine, clutch is tight, no problems.
      The reverse cable and lever are in tact and seem to move freely.  
      My question is this:  What does one normally have to do to get this thing into reverse?  I assume put it in neutral, twist the knob, kick the shifter down.  Does the brake need to be applied?  I'm not sure what's going on here, I suspect it's been 'modified' as it goes into reverse without the proper precautions, just not sure if the mods were external on internal.
       
      thanks
    • By Randel1
      I am trying to put a 1994 Suzuki 250 quadrunner back into service. I have it up and running like new but need to replace the plastics as they are brittle and crumbling due to age and sun exposure. I would like to purchase new parts either OEM or aftermarket but have had little luck in finding them. I would even consider used or salvaged parts in serviceable condition. Any help in locating these parts would be greatly appreciated. Thanks in advance.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...