Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Dominic Tiberio

Rebuilding a Zhejiang Yongkang 500W ATV - Need help with braking

Recommended Posts

I was given a Zhejiang Yongkang 500W electric ATV that has had all of the wiring and controls stripped  from it. I plan on installing a new speed controller, but I am having a hard time figuring out how to handle the braking. The 500W electric motor is connected to the rear axle by a chain/gear and it has mechanical disc brakes. I can't figure out how to handle braking without risking damage to the chain/gear and since it is stripped I don't have much to go on. I'm assuming that the brake was originally set to cut power to the motor when engaged, but it seems like it would still put a lot of stress on the chain/gear at any speed. I've never rebuilt an ATV or electric ATV, but I have a lot of mechanical and electronics experience. Any help or insight is appreciated!

Share this post


Link to post
Share on other sites


I've never messed with an electric atv. What are you trying to do with the rear brakes, replace the pads? Is the setup like:

 

Share this post


Link to post
Share on other sites

The brakes are one of the few things that weren't stripped. It is just a single disc brake/caliper on the rear axle and then two discs in the front. I haven't done an electric ATV either before but have a background in electronics engineering so I am fine with the basics. From what I can gather, the speed controller I bought, a YK31C, has a two-pin connector for the brakes and when the brake lever is engaged there are two wires that go from it to the speed controller and send a signal that kills the power to the motor. I guess I might be overthinking it and that is enough to limit the strain on the chain/gear as it brakes, but I just wasn't sure. Electric motors have a lot of torque, I just didn't want to trash the chain and/or gear or damage the motor. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tom Pavlak
      Hi Everyone - Need some help.
      Got a nice little 220...clean machine. wiring is a mess. I have a diagram however, the one I have has 4 wires coming from the ignition switch not 2 like mine. So, I cant trace wires properly.
      There is a white one that runs to the Solenoid, and a brown wire...from the Ignition...I dont know where its supposed to go. Also, on the Solenoid, there are 3 wires..W to ignition, B to start relay and B/Y runs up to the front of the machine...and is not plugged into anything...and there isnt a "Mate" missing it. How do they plug into the 4 open shovels by the 20A fuse?
      I'm pretty sure my Lights and start switch/Lights are correct.
      Problem I cant get anything...new battery...cant get the start button to work, cant get any power to the lights or switches...so I know something is not grounded or..
      Any advice would be greatly appreciated.
      Tom
    • By Chris2018
      Does anyone have the cdi box wiring? I'm trying to hook up aftermarket cdinbox and i keep confusing myself with the trigger signal wire trigger ground wire and 12v. Any help would be appreciated thank you for your input 
    • By amharrison24
      i have a 91 moto 4 100. has electric start only. for as long as i could remember we have always pushed start it. after riding for while you shut it off. you are able to hit the start button and it will start right up. anyone know where i should start with fixing this issue? im fixing it up for my niece. thank you in advance.
    • By colt
      Here is what I have collected over the years and maybe it will help someone else.
      There are so many and several are too large to upload as attachments, so see any thing you need just shoot me a PM and your email and I will get them on the way to you as fast as I can.
      Thanks
      50cc to150cc Service Manual For Tank Motorsports.pdf
      linhai-atv-service-manuals-linhai-300-parts-manual.pdf
      1986 CH250 ELITE SERVICE MANUAL.pdf
      Charging and ignition systems for atvs.pdf
      Chinese ATV Frame Diagram.jpg
      Chinese ATV Repair Shop Manual - Clutch Diagram - Exploded Views.jpg
      Chinese ATV Repair Shop Manual - Cylinder Head Diagrams.jpg
      Chinese ATV Repair Shop Manual - Torque Specifications.jpg
      Chinese ATV Repair Shop Manual - Valve Clearances.jpg
      Dinli-501-PARTS-DINONP.pdf
      Dinli-601-Parts2003BEAST-DIAMONDBACKNP.pdf
      Dinli-DL-5015erviceManual.pdf
      Dinli-DL-502PartsManual.pdf
      Dinli-DL-5025erviceManual.pdf
      Dinli-DL-503PartsManual.pdf
      Dinli-DL-601,DL-603ServiceManual.pdf
      Dinli-DL-603PartsManual.pdf
      Dinli-DL-604PartsManual.pdf
      Dinli-DL-701PartsManual.pdf
      Dinli-ServiceManual-150ccATV.pdf
      DTE150-2-150cc.pdf
      Eagle ATV Fender Body Parts Exploded Diagram.jpg
      Eagle ATV Rear Axle - Exploded Diagram.jpg
      GY6_150cc_ENGINE_PARTS_157QMJ_.jpg
      GY6_Top_End_Rebuild.pdf
      Leopard-parts.pdf
      Linhai_260servicemanual.pdf
      Odes-400-Repair.pdf
      Piston Ring Installation 4 Stroke Engines.jpg
      Roketa-ATV-10(ATV-DO43)-Repair.pdf
      Roketa-ATV-11(ATV-D037)-Repair.pdf
      SLA-120-PARTS.pdf
      SLGK-110-PARTS.pdf
      SLGK-150R-PARTSMANUAL.pdf
      SLGK-400R-PARTS.pdf
      SLU-500-600-700-PARTS.pdf
      slu700db-700UTV-Service-Manual.pdf
      tao-tao-atv-parts-cylinder-rebuild-kit-for 90cc-100cc-110cc-engines-p-13331.pdf
      Trouble Shooter Guide for BATTERY DRAINED Chinese Engines.txt
      Trouble Shooter Guide for NO-COMPRESSION.txt
      Trouble Shooting No Crank.txt
      Troubleshooting.pdf
      YX125CC BREAKDOWN.pdf
      _________________________________________________________________________________





      50 to 150cc GY6 Shop Manual.pdf
      Arrow 150 Engine Service Manual.pdf
      Eton Shop Manual YXT-150.pdf
      GY6 Shop Manual.pdf
      Yerf Dog Spiderbox GX150 Service Manual.pdf
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...