1992 timberwolf 250 2wd will only start if the neutral light is OFF

[VikingTrad3r 10]

picked up my third timberwolf 250 for my daughters.  these are great light weight little quads.

 

have a strange one for you.  the quad will NOT start in neutral.  it will start in first. 

if i lift up on the gear selector just enough to hear the little click (its not loud, sounds like a contact clicking, perhaps the neutral safety switch?) the light will go out, but it won't yet be in first either.  that is how i have shown my daughter to start it and she can.

 

id like to carry out whatever repair is needed.  i have the pdf of the shop manual but it doesn't really have a flow through diagram.

 

any help appreciated!  thank you.

i need to add something.  it feels like i can switch into another gear BELOW neutral.  

so if i switch to neutral, i can keep pushing the gear selector, and it has another click below the neutral.  the light stays on, and when i pull up into first it kind of feels like it has two positions it moves through to arrive at first.

[davefrombc 353]

Since I am not familiar with the Timberwolf , I  can  only guess at a possibility from your description. My best guess is the neutral  switch or the mechanism that activates it is either loose or broken so that it is out of position. It may be a simple adjustment and tightening required.  Open  it up and have a look. Starting in gear  is unsafe, especially for a  young rider.

[Impala_ss 3]

Yes sounds like it is a switch safety issue.  I would try and clean/adjust it first.

[VikingTrad3r 10]

im back with more info.

first, the reason it felt like i could shift below neutral is because the shifter leaver was loose. thats fixed. 

 

but the main issue remains:  here is an update, 

 

1. the reverse indicator switch is broken down on the left side of trans. i dont think that affects the starting circut though. ive ordered the switch. 

 

2. it WILL START if its in neutral, but only i have the neutral switch unplugged. IE, the neutal light is OFF. 

so something about the neutral light being ON when im in neutral, stops the quad from starting. 

its like there something reversed somewhere. 

 

the quad is ONLY. supposed to start when the neutral  light is on but instead it will only start when its off. 

[Mech 18]

Hope this Paste job works...

[Mech 18]

Yeah well that wasn't very successful now was it... I see there is a service manual in here though.. and that the circuit's got diodes in it.. and several switches.. 

Out with the test light..

[VikingTrad3r 10]

thnx. yeah i looked in my manual got the wiring diagram and it looks like its got to be in the relay. something is reversed in the relay. will inspect. wont be surprised if a bubba messed with it

[Mech 18]

Ha..  Could be.. 

I'd try and disconnect the switches and check they are adjusted and working right first thing though..

Edited December 31, 2020 by Mech

[VikingTrad3r 10]

switches are functioning properly. 

ive discovered something else. the reverse indicator light bulb is mia. so was the reverse switch. installed rev switch. 

had s bulb laying around, blew rev i dicator bulb immediately.  bulb mau be too wussy though  

 

anybody know where i get a replacement bulb?  this is for the little red bulb  the actual bulb  

 

[VikingTrad3r 10]

i tested the reverse position indicator light socket/receptacle and its showing 12.4 volts. the little bulbs i put in were rated for 2.4 volts. so i think that explains why they glowed very bright for a second then burnt out. 

 

so does anyone know where i can get a real reverse indicator light?  it would be the same as the neutral light id imagine

[Mech 18]

Auto parts store should have one.. Take a sample.

[VikingTrad3r 10]

found a local motorcycle shop they ordered me two for $3.25