Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

o... this is the deal.. im 15 i just got a job... and i wanna buy the widening kit from diamond j customs for my raptor... but i can only afford one kit at a time.... what would happen if i bought the front..... first./... how would it ride??

im about to order... so i need to know./..

please help

Thanx

Share this post


Link to post
Share on other sites


"URGENT HELP!!!!!" LOL. If you buy the front kit first? Then the front would be wider than the back. LOL. Doesnt mean you have to install it. Eitherway, installed or stting in your garage waiting for the rear axel to arrive it wont hurt a thing as far as how it rides. Go for it. And BTY, Im just messing with you. I was 15 once myself.

Share this post


Link to post
Share on other sites

yea, definatly. i bet if u jump with this widening kit it'll collaspe

but find some used full flight a arms or something off of ebay. jus some cheap ones, as long as they're in good condition.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By derek09
      hi is it possible to have the software for the Pim1 (ems) for raptor 700 thank you !!
    • By StolenATV
      My Children’s 50CC Yamaha ATV was stolen from just outside the garage. I did a little custom work to the front of it and added two LED headlights to it as well as a switch to the plastic handle bar cover. Our home sits well off the road and it was not something that was just in plane site so my fear is that this was planned over time and the thieves knew we had it and were just waiting their chance. We also had a 20 inch bike that was stolen as well, we were able to recover it however about a mile down the road as it was left abandoned. We didn’t know it, but we think the bike may have been taken a few days earlier. Now sure if both items were taken by the same person or just a coincidence Thanks for any help you might be.
      The post Yamaha 50 CC Raptor ATV Stolen appeared first on STOLEN 911.
      View the full article
    • By 2urb0liter
      Looking for front wheel assembly (hub, axle, rim, tire) for 1982 Honda ATC 110. 
      Let me know what you have and how much shipped to 58504. 
       
      Thanks!
    • By ray desocio
      I posted earlier looking for a wiring diagram, but maybe someone can help me with the problem if they’ve had it before. 
       
      The quad Will start and idle ok, when I open the throttle it will rev all the way up until WOT and then it dies back down to idle, and if I keep the throttle wide open it will rev back up. It will do this over and over and over. 
       
      I replaced the carb, (twice), Rectifier, battery, and spark plug.  The Stator ohmed out to the proper specs from dinli.  The other issue i can see is I’m not getting 12v on the choke circuit. The lights don’t work either. 
       
      possible bad key switch? Maybe the new rectifier is bad? All the contacts on the key switch also ohm out properly    
      comprsssion is up to 125 psi and spark is there. 
       
      Reed valves look great.....
       
      im at a loss. Any trouble shooting advice would be appreciated. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...