Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
I am looking to see why my 2005 Grizzly 660 won't crank. I have set the valves but suspect a loose timing chain.
When working to remove the valve cover I found a "cap tensioner case" - parts #25 - #299 on Babbitts site.
The cover seems to bridge the valve cover and the cylinder head. What the hell is it and what surprises will I find if I remove it?
Uncharted territory for me.
I bought a "project" Grizzly 660, I think it has been a few people's project. The PO had it for a while and did not have time to work on it. He said the battery was good, but I don't know how he knew because the display was blank, no lights and won't crank or run.
I found a nest under the front cover, by the CVT inlet, a chewed thru wire and a few more without insulation. Rewired those from the connector (black 3 wire to the display) and replaced the fuse as suggested by a search from this site. That got the display working and power to other circuits.
I replaced the aftermarket start switch with a used OEM switch from eBay. Then it would crank a little, and started once for a few seconds.
I'm a small engine mechanic - mowers, snow blowers, etc. In my small engine work I have had a number of rider mowers that would crank about a half turn and then stop. The owners have suspected a bad battery and changed it with no improvement. Setting the valves to spec usually fixed this.
I set the valves on the Grizzly without solving the crank problem. I wonder if the timing chain could be off - slipped a tooth.
I don't know any way to check for this without pulling the head and looking at the timing marks on the cam gear.
Is there another way to check for proper timing?
By fede hanssen
I have just got a 1995 Bayou 220 from my brother. It is in decent condition ant it has not been used much, yet it has been sitting idle for a long time (4+ years).
The plan is to overhaul it and move it to a location where it will be used 4-6 times a year, so, beyond having the battery charged, the idea is to have it ready and in good condition. It will be stored in a steltered place while waiting to be used.
My questions would be: 1. What things should I carry out as basic overhaul tasks / 2. What are the typical aches, things to watch out for in this model/year.
I definitely plan on changing all the fluids, filters, battery, cleaning the carb, etc. but any specific recommendation from your experience will be of great help.
thanks in advance!
By Frank Angerano
So I finally finished a bike I’ve been working on for my daughter.
Ive been practicing the vinyl thing for a while and making the camo vinyl prints as well as applying them.
This was a bike I dug out of a garage, original owner.
Compleyey broke it down and did my thing to it. So I put a girls touch on it and my 12 yo will be sporting this.
Dont be afraid to say what you think.
After riding for 20 minutes or so check engine hot flashes, I then stop and idle, fan will kick on run briefly warning goes out.
oil, coolant, are both full. The fan appears to be working but does not always come on when I stop and just let it idle while the warning
is flashing. Can turn engine off with warning flashing, fan does not run, can immediately restart warning resets does not flash fan does not run,
runs fine, a short time later warning will come back on. Trying to decide if this is a flow problem maybe thermostat or sensor problem. Have repair
manual on order has not arrived yet.
Similar Tagged Content
I have had my trx for almost a year now its been working great i put a full hmf exhaust an air filter and i got a dyno jet kit stage 2 i followed the instructions and just changed the main jet ..its been working fine but i feel that it can go much faster at top speeds and it starts choking and popping at 5th gear max speed??? how can i stop that and get more top speed??open the airbox?? help plz
MY trx has some mods like an full exhaust air filter and an oil filter my lid is on i bought a dyno jet kit stage 2 i read the instructions and changed the main jet supposibly but i didnt change any fuel needel on pilot jet when i turn on the bike its starts immidiatly but starts poopin and crackin on 5th gear when i go fast >>>?? why ...i feel like the bike should get some moore airshould i remove the lid or what??
My inside sources at Honda have told me that the new 450 will have an all new aluminum frame, EFI, improved geometry, and all new suspension. It should be out in 2010 unless they run into technical issues. The new 450R should put Honda back on top where they belong.
Recently Browsing 0 members
No registered users viewing this page.