Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
So my Yamaha grizzly 700 wasn't going into reverse for some reason but Jon and George figured it out on what to do to fix that problem for me. Jon Talks about how he was able to fix that problem my Yamaha Grizzly was having with the reverse.
On a side note we are so close to 1k subs! hell ya!
So my parents have not let me get my license yet and I need to get around to gets parts and stuff. Answer: Yamaha CW50 scooter. This is a 2-cycle self-mixing scooter that so far, I am really surprised with the power output and speed. It reaches about 45mph since the speedo has been disconnected and has plenty of power for two riders. Its stupid looking, but with some work and a title and plate, it'll take me around town.. My issue is this: No key. I bought it for $150 from a friend and he bought it from someone for $100 who wired in a switch in place of the ignition. That guy got it form his neighbor who's renter left it behind. The scooter will run with this switch on or off (kill switch on handlebar kills engine) To get it tiled and a plate so its road worthy, I need to get the ignition working either by a replacement key or a new ignition. All wires are cut to the ignition and the switch turned on the power to the signal light switch. Also, the 2-cycle oil was leaking out the carb, through the air filter and onto the scooter. also, it runs great, but its making blue smoke with throttle and the muffler is wet with oil.
(I have new signal lights for it btw) So the issues I have with it summed up:
No key (need new ignition) smokes burnt out headlight- can I replace them with LEDs?
By Flipper Tiffany Roper Jones
All I have been through everything. Bought brand new.
Throttle safety switch
Cam and rockers
Fuel safety switch
Everything every forum has spoken of I've bought sealed airbox completely tight unplugged black wire on trans. I have literally done everything in the book.Checked oil today full of gas anyone no anything what might b wrong. Next I'm taking head off and making sure valves seat any ideas.
So my latest find is a Moto 4 250. Looked in good shape, started right up but would backfire and die upon acceleration but you
could get it to go if you were good with the throttle. I figured it was the carb. was a brand new Chinese carb, he didn't have original.
I took it apart and cleaned it, only thing I found was some debris in main jet and the main adjustment on bottom was at 41 turns. Cleaned
it out and set at 2 turns, re installed. Starts up, runs better actually drove it but seems really sluggish, once I hit 3rd gear could barely pull
it. Rechecked everything, even ordered a new carb as I had this problem with another atv but still same problem. Now I pull it apart and
decided to check compression, I show only 85 psi. I checked valve adjustment (after aligning up cam gear to mark on case). to make sure not too tight still right at 85 psi.
I assume I need to pull the head and look at the valves, Any ideas I am missing something? motor does not smoke but is super sluggish.
The specs I find are off the downloaded manual of a 94 but figure should be the same. It states compression standard is 128 and Minimum is 114 and Max is 142
Any other Ideas before I tear it down? Thanks in advance Az
Similar Tagged Content
By Guest Fox300exchic
The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
Hi all, I try to find this manual in the threads but you have a lot of stock here
Cannot find this particular manual.
I found it for YFM200 but not sure if they are the same.
Thanks if you could help me with that.
Im new here so if I did something wrong, please tell me.
Recently Browsing 0 members
No registered users viewing this page.