Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
got 7 atvs off CL recently for a good price. one of which is a yamaha warrior. anyone know where the vin is printed on this bike? Haha good place to start as I do not know year or size yet. The former owner says needs exhaust ans and clutch work. he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears. things I see: clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box. I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first. also, battery (looks brand new, what a shame) is dead, 0 volts. Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last). any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like. lol I'm spoiled on my automatic polaris
By Brad Lawson
Hello all, I’m working on my sons 99 Yamaha Warrior 350. When I pulled the plastic cover off left side of engine, I can see oil leak at the seal. I pulled the bolt out and then the starter boss(I guess that’s what it’s called?) I can see that the boss doesn’t make contact with the seal. Is there a spacer of some type that slides on to the boss, to make contact with the seal? This seal is held in place with a plate with 3 screws in it. This boss slides into the bearing in the stator. I have been to parts websites and I don’t see what I’m needing. Maybe it’s just the wrong seal?
This thread is continued from old one at
Ok No crank on 1995 Bayou 220
Starter relay have ground at green (n/safety switch
12v at Brown (signal wire from key)
Have also Jumped the black wires still no crank.
relay does click when key turned on and off.
I know the kill switch is bad and all testing was done with it disconnected.
I did connect it for a moment just to see if it cranked and it did not.
I picked up my first ever ATV on friday. It's an 89 Big Bear. It has some cosmetic issues, but seems pretty decent mechanically. I did have trouble getting the idle tuned to the book spec of 1,300 - 1,500 RPM. I took the carb apart and cleaned it out. Somebody must have lost the spring for the pilot screw, as it's no longer in the carb. Also, I have a dual cable carb, I noticed all the IPL's show the single cable carb, but I see others on youtube had dual cable carbs. When I would adjust my idle speed screw, nothing would happen. I bottomed it out and it didn't seem to make much if any difference. When i pulled the carb apart I saw the screw doesn't even touch the linkage, it's too short. Do the two different versions have different length carb screws? I'm wondering if somebody lost the ordinal, replaced it with the IPL number for a single cable carb which is shorter, and gave up on getting the ATV to idle. If you hold the throttle just a bit to get it to the RPM range listed above, it "idles" great. Any ideas? Or any links to the dual cable IPL?
Have you guys have good luck with the aftermarket intake boots? Or is this a buy once, cry once deal? I'm guessing the OEM units last longer, but there is a huge price difference. If you have had good luck with aftermarket, where did you get it? My current boot doesn't seem to have any air leaks, but it's encased in JB weld...
I'm getting a 9th digit check sum error on the ATV when I put the VIN in. Has anybody seen this before on a Yamaha? The VIN number looks original as well as the paint around it.
Similar Tagged Content
By Guest Fox300exchic
The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
By Guest Fox300exchic
If we had a dollar for every time the question “Which is really faster, the 700 or the 450?” shows up in our inbox, mailbox, or voicemail, we’d be putting this magazine together from a bungalow on a barely inhabited tropical isle named Quadhama.
Hi all, I try to find this manual in the threads but you have a lot of stock here
Cannot find this particular manual.
I found it for YFM200 but not sure if they are the same.
Thanks if you could help me with that.
Im new here so if I did something wrong, please tell me.
Recently Browsing 0 members
No registered users viewing this page.