Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

MudWild680

Questions on maintenance

Recommended Posts

Just curious

When do YOU do the needed maintenance on your wheeler?

for example, fluids and such

how many miles/hours

I was wondering, do i have to use specific honda ATV oil in my honda ATV?

Thanks!

Share this post


Link to post
Share on other sites


Ok,,,,,,,,, Ive been drinking so bear with me.....

I usually change my oil every 2-3 Trips out just cause Im anal like that.....

However I would refer to your manual for Service Instructions.....

Your manual will ALWAYS tell you to use the Honda, Yamaha, Polaris Etc. oil for the specific brand you have.....however.....Any oil you buy with the Recommended weight will do.....

Hope this helped ya.....

Share this post


Link to post
Share on other sites

Use the specified oil. Honda and Yamaha will NOT buy you clutch plates under warranty cuz you used car oil in the crankcase and coated the plates with 'energy conserving 2' additives. Seriously.

Plus quad engines tend to run hotter than car engines so the blend is different. Same with bikes, they use the oil as a lubricant AND a coolant and need a fluid that can do both.

In my experience, I would pop the seat off, grab the owner's manual attached to the bottom of the seat and read every page OK? It could save you a bunch in the long run.

Share this post


Link to post
Share on other sites
Use the specified oil. Honda and Yamaha will NOT buy you clutch plates under warranty cuz you used car oil in the crankcase and coated the plates with 'energy conserving 2' additives. Seriously.

Good point.....However, in my 350X Ive been using just regular old Car oil with not one problem for almost the whole 10 yrs Ive owned it.....I replaced the Clutch when I bought it....I ride it hard....Clutch is still good.....Not saying anyone should buy Joe Blow Oil....Just saying it works for me....

Share this post


Link to post
Share on other sites

I agree with you there...

You know, I REALLY want to be your friend, but right after I joined you gotta a woody about me and whatever I did I AM SORRY. I want to be your friend and if there is a problem please PM me or put it RIGHT HERE so everyone can see it. I cannot imagine what I have done to you, but I want to be your friend again. OK? :rolleyes:

Share this post


Link to post
Share on other sites


I agree with you there...

You know, I REALLY want to be your friend, but right after I joined you gotta a woody about me and whatever I did I AM SORRY. I want to be your friend and if there is a problem please PM me or put it RIGHT HERE so everyone can see it. I cannot imagine what I have done to you, but I want to be your friend again. OK? :rolleyes:

Ummmmm,,,,,I dont know what to say.....Im sorry that you feel that way and I cannot for the Life of me remember why I would have gotten upset at you.....I may come across like that sometimes.....But usually after I type Im done......Actually,,,,,I would love for you to Mod this Section...You know much more than the Mods Collectively do:yes: Im giving advice from Personal experience on a 23 yr old machine:laugh:

If you would like to refresh my memory I welcome it...If not that is fine too.....

Peace Brotha:wink:

Share this post


Link to post
Share on other sites

It would not be the first time I was WRONG, I was concerned that you were pissed at me and I highly value your opinion and expertise.

OK

If I didn't piss you off than hopefully we are friends, yes?

That would be good eh?

I am looking forward to this now, instead of with apprehension as I have done in the past.

it's cool if I screw up then tell me! Best for the site, right?

As a friend I hope you are doing OK. If you ever need an ear and a beer, a meal and a sleeping bag, we can do.

THANK YOU for this. paul

Share this post


Link to post
Share on other sites

Oil threads are like what color is best or what brand Ford vs Chevy. I do not use the oem brand of oil in my bike or quads. Saying that though, I don't use car oil either. In most motorcycle and quad engines, the oil is in the engine and transmission. It sees a lot of sheering from the transmission gears. Car oil does not provide enough sheer stability for this application. If you want a great oil for ALL the toys, use a quality diesel engine oil. These are very sheer stable as the diesels have a gear drive train for the cams and water pumps and fuel pumps. I personally use synthetic oils. I know that a lot of motorcycle riders like the Shell Rotella oil. It can be bought at Wally World and is reasonably priced. I personally use Moble 5w40 Turbo Diesel oil. This stuff is designed for super high temps for the turbo, wide range multi grade and NO friction modifiers to mess with your clutch. It exceeedes all the specs your engine calls for. I also noticed that my 2007 V-Strom 1000 shifts smoother with this oil then several others I have tried, including the Suzuki 10w40 motorcycle specific oil. This is just my experiance, use what makes you happy!

Share this post


Link to post
Share on other sites


The numbers in the designations of the different oils being discussed refer to their viscosity, grade or weight. Don't confuse grade with quality. Viscosity and grade, for the purposes of this discussion, refer to an oil's ability to flow and lubricate. Therefore, a lower grade oil simply flows more easily than a higher grade oil.

At the heart of this discussion is temperature. Temperature changes an oil's viscosity. Hot oil is generally thinner than cold oil. A good example is Margarine. Margarine is a vegatable oil (mostly) that congeals at room temperature. Put it in a hot frying pan and it becomes a thin liquid quickly.

Oil in an engine operating at normal temperature serves several purposes. It helps seal unwanted gaps between internal engine parts, it carrys heat away from hot parts ...and, perhaps most importantly, it lubricates.

To lubricate, oil forms a thin layer, or film, between two parts. The parts slide on the oil film instead of against each other. Since hot oil is thinner (lower viscosity) it flows more readily than cold oil. If it flows too readily, however, it will flow right out from between the parts you wish to lubricate. Therefore, there is a "minimum" viscosity the manufacturer recommends to ensure the engine's parts remain lubricated when it reaches normal operating temperature.

Why is this important?

Let's look more closely at the specifications. 5W40 means the oil is a base stock 5 weight oil (weight is the industry term describing an oil's grade) with Viscosity Index Improvers (VII) added to make the oil less prone to flow out when hot. VII's are special polymers that change shape when heated, thus changing the oil's flow and lubrication characteristics. When the oil is cold (the "W" stands for "winter" BTW, not "weight") it will flow like the 5 weight oil it is. When the oil gets hot, though, that 5 weight oil gets too thin to lubricate. That's when the VII's must do their job; they unfold and help the oil lubricate like a thicker 40 weight oil.

An oil can only do its job when it is present. What I mean is, if the oil is too thick when cold, it takes much longer to pump it to the places inside the engine it needs to be to provide lubrication. In fact, unless you are a racer spending the majority of your riding time with the engine RPM north of 8,000, most engine wear due to friction between moving parts occurs right after start up -- especially when it's cold outside. Why? Because the oil takes a few minutes to flow to all those critical parts.

Hot, thin oil is much easier to pump around your engine. For example, it's easy to suck milk through a straw. Now imagine sucking butter through that same straw. Cold oil is thicker, and takes longer to pump around the engine. Therefore, there is a "maximum" viscosity a manufacturer will recommend to allow oil to flow to critical engine parts when cold.

This was posted on another board I frequent......Thought it might help here........:cheers2c:

Share this post


Link to post
Share on other sites

so..

in other words..

and in words that shouldnt confuse me anymore then what i already am...

I shall just stick with the Honda motor oil

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Chase Cook
      Hi I have a 1991 Honda trx200d type 2 ATV and need to know how to adjust the valves on there. The valve adjustments are on the side of the head and looked up videos in there is no videos at all on how to adjust them. I'm taking the head back off to adjust the timing because it's making good spark and getting gas but it's not firing, trying to start but I'm thinking it's because of the adjustments are way out of  line. And I didn't take a picture of how they were before I took the head off.
    • By bellssn690
      Hello all. I'm a new owner of a like-new 2013 Rancher. I'm hoping to get enough information to keep/maintain my new atv. It's in great condition but I've noticed that it wants to die after running great for a while and I come to a stop. It's like it chokes itself out. Not sure why but it'll start up again but it's in such nice shape I want to make sure I keep it that way. Thanks for any advice and help in advance.
    • By JacobSlabach
      recently picked up some project bikes off CL for cheap.  got a honda fourtrax (the ancient 4x4 kind with the straight axle in the front as well as the rear and a back-up kick-start)  plastics are crap, but my goal is to get running like a champ and patch the plastics up and sell to one of my many friends that want a reliable 4x4 for dirt cheap and doesnt care what it looks like.
      so the former owner says it needs carb rebuilt, but its sat for 3+ years since so who knows.  things I see:  carb is missing (he gave me a box of parts along with the bike), engine turns over and feels good with kick-start, brakes need work, battery missing (That always puts me off, cause then I know most likely someone's been tampering with the electrical.
    • By Gary Patch
      hi have really old Honda 4x4 how do I find out model no  etc as need new starter motor think its 350 cc but not sure thanks in advance
  • Similar Tagged Content

    • By Mike8623
      Im looking for a atv fertilizer spreader that will spread bagged manure like Walmart sales. Does anyone have any recommendations or what have some of you used that will work with the bagged manure/fertilizer.
    • By chevyboy
      AL righty I did some trading around this weekend and ended up picking up a few 4 wheelers for cheap. I ended up with this one for $500 in it total and well the guy told me it dropped a valve. I haven't really messed with it at all. But this weekend I am going to try and start working on it some to get it running before winter time frame. So what I am asking is a couple of questions.
      1. First off where do I start I tried pulling the pull cord and could not get it to move at all.
      2. I need to get a service manual for this 4 wheeler where can I get it downloaded for free?
      3. what do I need to look for and how do I go about this really. I do have experience with 4 wheelers but this one is a little different to me than others because its a V2 and I have no clue where to start internal on the engines. Most of my experience is on the outside portion of troubleshooting on theses wheelers.
      Please no smart butt answers as i am new to here but just wanted opinions on where to start. Please and thanks wink:
    • By toonces
      Got my first quad this past fall a 2011 Grizz 700 EPS, and now that spring is getting close I'm thinking about getting back to work on maintenance stuff. So couple questions...
      1. What are some regular maintenance points that are done in the spring on these machines?
      and
      2. What are the regular maintenance points that are done every so many miles that I should look to do?
      Other than changing out a torn CV boot and cleaning some crap out of the air intake foam in the fall I really haven't done anything to the Grizz. So not knowing its maintenance history I'm assuming it's due for everything...all fluids changed out etc.
      Oh btw it's only got about 750 mi on it right now.
      Thanks I'm all ears
    • By Tivy
      My boot on the drive shaft came off this weekend. When I tried to put it back on it appeared to be about 2" too large. Any explanations????
      Also when the boot cam off, there was oil in the boot. Is this normal???
      Thanks for your help.
    • By toonces
      Anybody know the axle nut size on a '11 Grizz 700?
      Also, could use a link to maybe a youtube video or a how to thread explaining how to change out the lower front boot.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...