Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

What offroad vehicles would you buy if money was not a conern?


Recommended Posts

and for the forum i would pick up a jeep cherokee prob 94 or a 96 with manuel 5 speed tranny switch out the axles, add some here and their stuff to the engine add the catback exhaust to it possibly borla get me a 4 inch lift or 4 1/2 and 33 inch mud tires possibly super swampers, nothing to fancy just want something to go through the mud

for atv a arcitc cat trv with crush locks 32 "gorilla tires and gorilla axles 5 inch lift and get steel horses in texas to trick out the motor so its a 1000cc atv... but i would only do that if i didnt live in new york cause their is no were to go with something like that were i live

and a popo 850 xp with 29.5 laws

Edited by outlander560
Link to comment
Share on other sites

yea the budget lifts arent bad was thinking about get a 3 inch and just adding the blocks to the back and front so i can get more lift from that... i was thinking ebay but i dont want to pay that much and find out its missing bolts shocks or something that but thanks for the info... then again im 16 so i think ill settle with my jeep for now ill pay it off and spend money on a lift later down the line... but wat kind of lift u get?

Link to comment
Share on other sites

yea the budget lifts arent bad was thinking about get a 3 inch and just adding the blocks to the back and front so i can get more lift from that... i was thinking ebay but i dont want to pay that much and find out its missing bolts shocks or something that but thanks for the info... then again im 16 so i think ill settle with my jeep for now ill pay it off and spend money on a lift later down the line... but wat kind of lift u get?

1992-1998 Jeep Grand Cherokee - 3.5" Suspension Lift Kit (EZ-Ride) - Jeep Grand Cherokee Lift Kits

Check this deal out. 3.5 for under 600. damn good deal.:huh:

Link to comment
Share on other sites

  • 2 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By McG75
      Hello I’m new here and was wondering is anyone knew of good replacement part numbers for front struts and rear shocks for this atv? I think I’ve found a new rear shock, that looks like the original but there is no dimensions or anything and was wondering if there are any afterMarket new front struts available. I know it’s a long shot but any help would be appreciated. 
    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By Admin
      View File 1984-85 Kawasaki Tecate ATC service manual
      1984-85 Kawasaki Tecate ATC service manual
      Submitter Admin Submitted 03/24/2024 Category Kawasaki ATV  
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...