Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Ajmboy

Well Motor Hunter 650 4WD Buggy

Recommended Posts

I just found this online and thought it looked pretty cool. It's some off brand by Well Motor.

Hunter 650 4WD Buggy Web I_Logic

Hunter%20650cc%20FR.jpg

Hunter%20650cc%20FL.jpg

Hunter%20650cc%20front.jpg

Hunter%20650cc%20rear.jpg

650cc%20Buggy%2005.jpg

Engine Type 4-Strokes, Water Cooled, Fully-Automatic

Cylinder Arrangement Double Cylinder

Transmission System Reverse N1230 Shaft Drive 4WD

Bore x Stroke (mm) 57x57.8

Piston Displacement (cc) 147.4

Compression Ratio 8.4:1

Maximum Power (kw/r/min) 14kw 4500r min

Maximum Torque (N.m./rpm) 14/kw/4500r

Starter System Electric/ Kick

Lubrication Forced pressure(wet sump)

Transmission Shaft Drive

Overall LxWxH (in) 88x50x44 inch

Wheel Base (in) 60

Seat Hight (in) 44

Min. Turning Radius (mm) 2800

Ground Clearance (in) 4

Rider Capacity 2 Person

Dry Weight (lb) 275

Brake (Front/Rear) Drum/Disc

Tyre, Front 25x10x12

Tyre, Rear 25x10x12

Ignition Type C.D.I

Fuel Tank Capacity (L) 12L

Engine Oil Capacity (L) 1L

Gear Oil Capacity (L)  

Front Suspension Independent,Telescopic Arm

Rear Suspension Swing Arm

Parking Brake Mechanical Lock

Max. Load Capacity (lb) 210

Max. Speed (mi/hr) 45

Battery 12V-9A

PACKING SIZE (in) 226x132x117 cm /G.W. 435 KGS NW: 410KGS

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
    • By Mike Iadonixi
      Hi my son's 2005 Honda recon engine is seized any ideas on what or where to get another engine 
      Thanks to you guys i fixed my other son's four wheeler last month
      any help would be greatly appreciated
      Thanks
      Mike
    • By Wayne Starz
      I have a 2005 Suzuki Vinson 500cc automatic 4X4. I can only shift it in to park & High gear, it will not go in low or reverse, what's the issue & the fix?
    • By gouletp
      The thing sat since Christmas 2018 and while I decided whether to replace the starter (which I finally did today).  I am not sure if I added fuel stabilizer or not but chances are good I did.  I kept the one year-old battery well charged during the winter.  It turns over well but won't start.  I have a blue spark on a brand new plug.  When I pour a bit of fuel down the cylinder, the engine starts and runs for a few seconds (once for as long as about 8 sections) and then dies.  Even before adding fuel to the cylinder I noticed that the spark plug was wet with fuel.
      The air filter looks a bit dirty so I removed it just to see if the engine would start better but it made no difference.
      If the fuel did not contain stabilizer then the carb may be gummed up.  I don't really want to remove the carb to do a thorough cleaning.  Is there a product I can spray into the carb while the engine turns over that will clean the carb?
      Any other suggestions?
      Thank you
    • By David Cameron
      The small waterline insert for the hose that goes from the water pump cover to the thermostat housing has corroded off. I only need the insert on top and behind the thermostat housing that the hose goes over and can't find just the insert. It looks like it may be pressed in. I've have been told the entire motor housing needs to be replaced. The pic with the red line indicates where the hose and insert would be and the insert looks like the pic of the water pump  Any ideas would be really appreciated.
       
       



  • Similar Tagged Content

    • By BigRuss
      I have a Kawasaki  bayou 4WD that started squealing when giving it the gas from a stop. It almost sounds like a fan belt but the dealer replaced the belt about 30 hours ago, so I don't think it is that. As best as I can tell, it actually sounds like it is coming from the front end. Once I am running and moving at a speed, I don't hear the squealing anymore. My first thought was to put fan belt dressing on the fan belt, as a quick test for the problem. It makes the noise when hot or cold.
      Another problem, that started before the dealer changed the fan belt, is that you give the quad a little gas, and nothing, give it more, and nothing, give it more, and it lurches and takes off. The dealer said it needs a new clutch, which I don't buy. less than 400 hours and it needs a clutch? I would say it needs an adjustment. When the quad is cold, as in I just started it for the first time in hours, it does not lurch. It is just fine. It lurches only when it gets hot, as in when you can hear the fan once in a while to cool the oil.
      Any help or insights would be great.
       
      Russ
    • By Quadguy420
      I recently bought a 2002 prairie second hand for 2000$ .. just for the record it has 28 inch zillas on it .. anyway . whenever i put it in any gear , it takes a second for it to engage ... and when it does it clunks into gear ... is that common for that quad for that year ? or is it cause the previous ower didn;t replace the clutch springs to heavier duty ones ?
    • By stewart1
      i just bought a 2005 suzuki 700 king quad it runs fine when i push the 4x4 button in but as soon as i flip up the differental lock the motor starts cutting out can anyone help please.
    • By Cford
      I put to much oil in my motor. Took quad out riding, rode for about 3 miles then it started bogging down, then died. Now it won't start. Any ideas as to what happened in my motor??
    • By gyminis
      I have a 1996 suzuki king quad lt-f4wdx 280cc and am considering haveing it rebuilt as a seal is bad and cannot be replaced w/o tearing the motor apart! I need to know the average price range to do this!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...