Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
PA Residents, please take a moment to send an email supporting this to [email protected]
This week, the Department of Conservation and Natural Resources (DCNR) plans to outline proposed policy changes for ATV trails on state forest lands. They will also be seeking public comment.
Pennsylvania has more than 260 miles of ATV trails in state forests. The department is reviewing its policy to respond to increasing demands for riding opportunities and well as interest from local governments in expanding tourism.
“The purpose of the policy is to provide guidance to DCNR when acquiring, developing and managing lands for ATV use by the public,” Secretary Cindy Adams Dunn said.
There had been a moratorium on new trail development, but the policy revisions now authorize DCNR to consider new ATV trails and connectors on state forest lands.
“New ATV trails will be considered, while still balancing the protection of natural resources as outlined in the Environmental Rights Amendment to the Pennsylvania Constitution, and the needs of all types of recreational users on DCNR lands,” Dunn said.
In a 2016 survey of ATV users, more than 4,800 responded with many indicating a strong desire for more long-distance trails. Pennsylvania has around 285,000 registered ATVs. On state forest lands, ATV riding is allowed only on designated trails.
Public comment will be taken at a meeting in Harrisburg Wednesday, January 22, from 10 a.m. to noon in Room 105 of the Rachel Carson State Office Building. Written comments can be submitted to [email protected]
The deadline to submit comments is March 27.
More information about ATV riding is on the DCNR website.
By George Henry
I just watched this video I made ten years ago. It made me laugh. I was riding a 1985 Honda ATC 200X. It's hard to film yourself so I had to position the camera to film me. May flies out th wazoo, but I HAD to ride. I hope you get a laugh.
Here is the link:
By Dwight Williams
Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00. It's been sitting outside with no carburetor on it for about a year. Its rusty, missing some parts, wiring is all cut up and spliced etc. No seat, no racks but the plastic is all there minus the headlight housing. Anyway, who can pass up a $40.00 quad right? I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water. I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine. I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark. Did a quick compression test, 70 lbs. Wet test bumped it up to 90. Ok, so rings and cylinder washed out with water for a year, not too surprised. I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show it's got life. Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either. The compression is now around 60.
Anyway, my question is....is it worth it to try to get this thing going? I tore the top end down today and the cam and one of the rockers is pretty worn. I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well. Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again. Much less just to make it run and use as-is but I won't really like it until it's right. I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much. I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down? I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
I'll get some pictures today if anyone want to see them.
Similar Tagged Content
Recently Browsing 0 members
No registered users viewing this page.