Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

bklynhunter

new guy w/02 big bear

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Colin Davis
      I recently acquired a Yamaha bear tracker 250 that does have a wiring harness.  Does anybody have a wiring diagram for the 250s. Also if you have a pin diagram that tells be the colors of the wires going to the cdi and rectifier or just a picture of the plugs would be much appreciated. I can’t find anything on the harness online. I have all of the switches and stuff and I plan on just build a harness myself because I can’t find one to buy.



    • By payne
      Have an Bear Tracker 250. Dont have the manual or any literature to help with. Anyhow, starts with pull start in gear, and electric starter doesnt work. Also, neutral light doesnt come on. Where should I begin?? Need some direction on troubleshooting all this. Thanks a million.

    • By PKR
      I rebuilt the carb on a 1989 350 Big Bear. This is a Gen 1 carb ( 2 cables running to throttle).
      Quad starts and runs but I have fuel leaking from the air intake.
      Is the float set to high / low?
      Does the needle for the main jet need adjusting? I have it on the center groove ( 2 groves above and 2 groves below).
      All jets are new, float and needle and seat are new.
       
      Thanks for your help
      PKR
    • By fartknocker
      My experience for my 98 sportsman. .keep on mind it has the smaller rear rim so my tire choices are not all that great ...
      Best...  Goodyear mud terrain. Long lasting awesome all around great tire.  No longer available of course 
      Worst. ...super swamper vampire . Too soft. Ended up on gravel a few times over a few months of winter snow riding. . Burned down from 1.5 inch paddle to 1 inch in no time. Junk. But if you are able to 100% stay in soft terrain they are insane 
      Current. . Mud lites . Pretty decent.  But I miss my Goodyears
  • Similar Tagged Content

    • By YamahaBB350
      I have a Yamaha Big Bear 350 and the reverse doesn’t work, it shifts from low to high easily but it won’t go back to reverse. I’m new to this stuff, so I’ll take any help. Any ideas? 
    • By Christopher Williams
      Hello all, 
      i just rebuilt the top end of a 99 Bear Tracker 250 and it can’t get it to hit off of gasoline or starter fluid. Occasionally it will backfire. Right now I’m just trying to get it to fire off without the carburetor like I’ve done a thousand times before with other engines. Usually there is no response, but occasionally I get a backfire through the intake. ISeems like it’s out of time, but I don’t see how that could be possible. 
      Here’s what I know:
      1. compression 120psi
      2. all timing marks are lined up after numerous revolutions. 
      3. Strong spark. 
      4. Valves adjusted correctly. 
      Thanks in advance. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...