Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

JC-Outlaw

2007 Polaris Outlaw 525 IRS rear cv boot replacement

Recommended Posts

If anyone can offer any assistance in replacing the rear cv boot any help would be appreciated. I am having trouble getting the rear shaft off of the quad. I figured the part would have some sort of manual but that would be too easy. Thanks again!

Share this post


Link to post
Share on other sites


Should just pop out with a little persuasion. Stick a small pry bar between the cv joint and the case and give it a little push while pulling on the cv joint. there is a snap ring that sits inside a recess. Just dont go all prime-evil on it.

Share this post


Link to post
Share on other sites

Remove the rear wheel and hub. Remove the spindle, remove the nuts and pins that secure the ball joints and then rap on the side of the spindle to knock the ball joints loose. Once you have the spindle off, the inner part of the half-shaft will unbolt from the rear carrier.

Share this post


Link to post
Share on other sites
Should just pop out with a little persuasion. Stick a small pry bar between the cv joint and the case and give it a little push while pulling on the cv joint. there is a snap ring that sits inside a recess. Just dont go all prime-evil on it.

Does the retaining clip inside the boot have to come out (and if so how?) to remove the axle, or just by pulling the axle will it come out?

Thank you again for your information!!

Edited by JC-Outlaw

Share this post


Link to post
Share on other sites

If I am not mistaken, the inner part of the joint is bolted to the brake disc or the sprocket depending on what side it is on. As far as the circlip goes, I think it just holds the joint to the half shaft. It shouldn't need to be removed unless you are actually replacing or rebuilding the joint itself. What Voodoo is referring to is the snap ring that holds the inner side of a traditional cv joint in, that type just slides straight into a splined socket usually on a differential. I believe that yours is a bolt on type.

Once the half shaft it off the machine, just pull back the boot you are replacing, or cut it off for that matter and the joint should slide right apart. Then slide the new boot over the shaft and put the joint back together and install the retaining straps on the boot. Make sure to re-grease the joint.

Share this post


Link to post
Share on other sites


If anyone can offer any assistance in replacing the rear cv boot any help would be appreciated. I am having trouble getting the rear shaft off of the quad. I figured the part would have some sort of manual but that would be too easy. Thanks again!

There is a complete how to at atvwheelin.com in the tech tips

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ajmboy
      View File 2018 Textron Off Road Alterra 500 Service Manual
      2018 Textron Off Road Alterra 500 Service Manual
      Submitter Ajmboy Submitted 12/16/2018 Category Textron Off Road ATV  
    • By Sonders
      It appears that the Service Manual thread at top of forum is dead as all the links no longer work.  I'm actually looking for service manual for a 2000 KVF300 Prairie that I just picked up.  Does anybody have link to one that they can share, or know where I can find one?  Thanks in advance for any help.
    • By DUBLT
      Looking to purchase a windshield for my ATV, suggestions of what to buy with quality in mind and will fit without doing any modifications. 
    • By Jon Emrich
      Does anybody out there have a link to the PDF manual download for a 1988 Suzuki Quadrunner LTD 4 x 4? If not does anybody have this on digital file they could possibly email to me or guide me in any direction to where I don't have to buy it? Thank you very much everybody in advance! Have a great day!
    • By Jun Dela Merced
      NEW HERE IM NEEDING SERVICE MANUAL FOR 2014 CAN AM OUTLANDER XMR 1000
       

  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...