Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

FIREMAN71

Honda 300 Fourtrax Carb Adjustment

Recommended Posts

Cleaned carb on my 300 fourtrax over weekend. Cannot seem to get (mid throttle) stall out of it. Does pilot adjustment mean that much in regular elevation (oklahoma) i set it where it was (2 1/4) turns out

Share this post


Link to post
Share on other sites


2 1/4 on airscrew is correct. Pilot jet controls idle. Did you check jets to make sure they were not clogged. Sounds like a main jet issue. Shoot madkaw a message, he can probably help you out.

Share this post


Link to post
Share on other sites
Cleaned carb on my 300 fourtrax over weekend. Cannot seem to get (mid throttle) stall out of it. Does pilot adjustment mean that much in regular elevation (oklahoma) i set it where it was (2 1/4) turns out

* Adjusted thread title to include model and make.

What year is this quad?

Share this post


Link to post
Share on other sites

Turns out choke was partially sticking. Not enough you could tell at idle but would fall on its face at mid range. Thanks for the post

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By PolarisRich
      I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought.
      My bike is a 2005 Sp 500 HO.
      I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at.
      Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts)
      [ATTACH]1021[/ATTACH]
      then the side cam cover (5-8mm bolts).
      [ATTACH]1023[/ATTACH]
      Also remove the plug in the recoil cover (14mm bolt) to see the timming marks.
      [ATTACH]1022[/ATTACH]
      Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke.
      The best was to tell that your at TDC of the compression stroke is to rotate the engine until the
      timing marks are parallel to rocker cover gasket surface.
      The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line.
      Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on
      the flywheel into the center of the hole.
      [ATTACH]1023[/ATTACH]
      Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly
      [ATTACH]1024[/ATTACH]
      [ATTACH]1025[/ATTACH]
      To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs.
      The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple.
      I'd give it a 4 out of 10 on the skill level scale.
      I hope this helps!
      Thanks Rich





    • By Eddie Rahm
      whats up fellas....the white wire going from the throttle body came unplugged from the circuit  board and im not sure where it plugs back in to ? i see where the red wire goes but im not sure where the white wire goes...im not even sure what those wires do..any help would be appreciated..thanks. 1996 polaris sportsman 500 4x4 push button awd.
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By thegipper
      Have replaced, Carb, fuel pump, CDI, plug, coil,fuel filter. Will crank but not srt. Getting spark and battery is fully charged 12.6V
      Any suggestions????
       
      Thanks
    • By Travis Johnson
      My 1988 Honda 300 fourtrax has a short all of sudden neutral light works but when I put on headlight nothing can't start it unless kick start please help
  • Similar Tagged Content

    • By Ashton Crawford
      Hello everyone, i have 2000 Polaris Trail Blazer 300 I’ve been stumped on for weeks. I’m having a lot of issues starting the quad. I cleaned the carb spotless because I thought it was a carb issue and bought a new fuel line because it wasn’t getting fuel. The carb gets fuel perfectly fine now but it won’t start. The spark plug I a little worn out but it’s good enough for just one start. The only time it does “start” is when I spray starter fluid into the carb. But it never stays on. It’ll start for a bout a second then just die out immediately even if you’re giving it some throttle and the choke is on. I have no clue what I should do. If you need more information, have questions, or have any slight idea what the issue would be and how I could resolve it. Please reply ASAP. Thank you.
    • By Alan Callison
      OK ya'll.My son bought this thing and was told its a Kaw Bayou 300. Maybe. I cant find any numbers on it.The one tag I did find its so faded as to be unreadable. Its a long shot but maybe someone can help ID it. Thanks in advance.









    • By Jeff Wharton
      I have a 2000 Arctic Cat 300 4 wheeler. I have been having some carburetor issues. So i bought a new carb. Now I'm having these issues. The unit will start and idle fine, when i go to accelerate it wants to cut off. So i checked to make sure it was getting gas and the fuel filter will be full of gas and then once the carb opens the filter drains down and will not refill quick enough to run. So i checked to make sure gas was flowing to the filter and it is flowing fine through the line. I remove the filter and run the gas line directly to the carb and the engine idle fine and then it will run good as i ride it for about 10 minutes then it will start with the same issues again i cannot accelerate enough to move the 4 wheeler. Every time i accelerate the unit will cut off. What is wrong with this thing. My 400 Arctic Cat is doing the same thing except it will backfire, I'm lost i have tried everything i know to do, what am i missing here. Thanks for your help
    • By Maurais
      I’m looking for new replacement shocks (front & rear.) on my 1997 Kawasaki Bayou 300 2x4. New OEM shocks are upwards of $400. I haven’t pulled the rims off to check the eyelet to eyelet length but I’m hoping an expert on this site does know( I called Kawasaki direct yesterday and they were of know help.) Any technical help would be appreciated. TY fellow members. Vic
    • By scottj11
      Hello, how are you'ns doing? I'm in the process of tearing my Kawasaki Bayou down to fix a rattling noise and an oil leak. I'll probably be asking questions about this project. My step-son has an Arctic Cat 300, he was riding yesterday and when he turned it off it was running fine, but it won't do anything. The lights come on but it won't turn over or anything. Does anyone have any ideas on what might be wrong? TIA
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...