Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By marek porowski
It’s kind of ATV related question as I need new trailer tires to tow my 4 wheeler.
Does anybody have any experience with loadstar 12” trailer tires ?
There is not to many choices for trailer tires here in Ontario and I was wandering if somebody can recommend me something.
By colin james
View File 1996-2000 Polaris Sportsman 335/500 Service Manual
This is the factory service manual for the polaris sportsman 335 & 500.
You can download the section you need or download all of the chapters for the complete manual
Submitter colin james Submitted 10/19/2018 Category Polaris ATV
I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought.
My bike is a 2005 Sp 500 HO.
I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at.
Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts)
then the side cam cover (5-8mm bolts).
Also remove the plug in the recoil cover (14mm bolt) to see the timming marks.
Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke.
The best was to tell that your at TDC of the compression stroke is to rotate the engine until the
timing marks are parallel to rocker cover gasket surface.
The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line.
Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on
the flywheel into the center of the hole.
Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly
To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs.
The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple.
I'd give it a 4 out of 10 on the skill level scale.
I hope this helps!
Similar Tagged Content
Hey all, I am new here, new to quads well owning them anyway, I am a certified Chrysler mechanic and we just got 3 quads. a 99 Honda trx300 fourtrax 2wd, and 92 Yamaha YFM80 Badger, and a Suzuki lt50. So far it has been a great thing for me and my boys to do together. Looking forward to learning a ton of information.
New guy from Stafford, Va. I'm about an hour south of Wash, DC and and hour north of Richmond, Va. My sons and I love to go wheeling. We have been going to Taskers Gap in Edinburg, Va. We have four ATVs: 1991 Honda Fourtrax 300, 1995 Honda Fourtrax 300, 1996 Yamaha Big Bear 350 4x4 and an Arctic Cat 500 4x4.
this is my 1st atva kawisaki bayou 300 4x4. its alot of fun. im in the process of retireing from farming so i have plenty of time and plenty of places to ride. iv been useing the beast for checking fences and my trap line. i wasnt sure how it would do in the snow, thats why i call it the beast, havent been stuck yet. looking at the map it appears im the only one on here from s dak. i guess s dak. is one of the few states you can lisence and drive atv's on public roads. not sure if ill do that yet or not. theres nothing i have to work on yet on the beast but im sure ill eventually be looking for a manual to make adjustments etc.
Recently Browsing 0 members
No registered users viewing this page.