Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Blaine

1996 Yamaha Kodiak 4 to 2 wheel trans kit?

Recommended Posts

Hi All. I'm wondering if anybody has heard of a conversion kit for a 1996 Kodiac 400 so that I may be able to switch from the constant 4 wheel drive to 2 wheel drive and back to 4 wheel when required. Thanks Blaine

Share this post


Link to post
Share on other sites


yes they do warn makes exactly what you need. Its called a warn 424 select. its not cheap will probably run you 280 to 360 bucks

Edited by outlander560

Share this post


Link to post
Share on other sites

Thanks for the help. Warn has discontinued this part in 2008 but I will shop around and see if I can find one.

Share this post


Link to post
Share on other sites

That's the only kit I know of, but it's not listed for a Kodiak. may work if it's a similar set up to a Foreman or Rancher. It is discontinued, just try to buy it elsewhere (after you verify it will work)...here are some other links:

424 SELECT

WARN 424 SELECT 300 PRAIRIE 64628 P W64628 at Underbid.com

High Lifter ATV Products & Accessories - WARN 424 Select - Honda 400 Foreman (98-01)

Share this post


Link to post
Share on other sites


theirs 2 yamaha 424 selects on ebay forsale a 97-99 big bear one that should work with your kodiak and a 96 yamaha wolverine that would probably work as well

Share this post


Link to post
Share on other sites

I would thinnk that it should work. I know my friend has it on his rancher and it works perfect for disengaging the 4wd.

Share this post


Link to post
Share on other sites

Hey guys thanks for all the help, finally talked to someone who had a definate answer from ATV Direct

and confirming as I found out by cross checking oem parts at BikeBandit.com unfortunatly the Warn 424 is not compatible with the Kodiak. Oh well Dad is just going to have a keep a little extra psi in the fronts.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Steve Howard
      Ran find shut down the quad next day would start and idle when you try to accelerate it would start popping through the carb got a rebuild kit soaked it in chem clean after break down for 12 hours on slow vibrate reassembled and adjusted per manual still the same thing any help would be really appreciated thanks and happy ridding  
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By Romain Catinaud
      Salut! J'ai acheté un quad 450 wolverine de 2006 mais je ne trouve pas le circuit coupé au guidon n'existe pas sur 2006? Merci les gars
    • By Craig Butterworth
      Hi, i'm looking for some help and advice with my arctic cat quad, its the first of the arctic cat quads as far as i know, manufactured in 1996 the bearcat 454. i have owned the quad for about 10 years now but just recently it has developed a problem with reverse gear, reverse wont engage any more like it used to 😕 the cable and handle is free but there is no movement the gearbox end, can anyone give me a heads up of what is involved to fix this? 🤔
      If anyone has a service/repair manual available for it as well that would be greatly appreciated! 🙂
    • By JacobSlabach
      recently picked up some project bikes off CL for cheap.  got a honda fourtrax (the ancient 4x4 kind with the straight axle in the front as well as the rear and a back-up kick-start)  plastics are crap, but my goal is to get running like a champ and patch the plastics up and sell to one of my many friends that want a reliable 4x4 for dirt cheap and doesnt care what it looks like.
      so the former owner says it needs carb rebuilt, but its sat for 3+ years since so who knows.  things I see:  carb is missing (he gave me a box of parts along with the bike), engine turns over and feels good with kick-start, brakes need work, battery missing (That always puts me off, cause then I know most likely someone's been tampering with the electrical.
  • Similar Tagged Content

    • By Craig Butterworth
      Hi, i'm looking for some help and advice with my arctic cat quad, its the first of the arctic cat quads as far as i know, manufactured in 1996 the bearcat 454. i have owned the quad for about 10 years now but just recently it has developed a problem with reverse gear, reverse wont engage any more like it used to 😕 the cable and handle is free but there is no movement the gearbox end, can anyone give me a heads up of what is involved to fix this? 🤔
      If anyone has a service/repair manual available for it as well that would be greatly appreciated! 🙂
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
    • By ej200421
      i was wondering if i could get some help. i been trying to locate where the fuel and air adjustment screws are located on my 95 kodiak 400. i think i found the fuel screw.. i know where the throttle adjuster is but i cant find the air screw. or is there an air adjustment on these carbs?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...