Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

tigerorange

1998 Artic Cat 454 4X4 Starting Problems

Recommended Posts

I'm a newbie with ATV's and was given a '98 454 4X4 Artic Cat by my brother. It has been sitting for about a year without being run so I changed the oil, charged the battery and replaced the spark plug but I can't seem to get it to start. It only has 689 hr

Where should I start the trouble shooting? Any help would be appreciated.

Thanks

Share this post


Link to post
Share on other sites


Congrats on the atv.

First, with key on , is there power? What happens when you hit the start button? I know you charged the battery, but it still could be dead. Did you try the pull start? Is the choke working properly and on when starting?

Share this post


Link to post
Share on other sites

There is power. The lights come on and the green light highlights the N (neutral). I have tried the pull start with no luck. When I hit the start button I can hear the motor turning over similar to when i pull start. Is the chock the right beside the start button? It seems to be worn and I'm not sure if full choke is all the way down or up. How would I go about check the choke? Thanks for your help

Share this post


Link to post
Share on other sites

Make sure the fuel switch is not off or on reserve. Also some quads you need to hold the handbrake when starting it or put it in park. when you crank it, does it seem the starter is moving slow? You may want to add a booster to the battery if so. Maybe the battery is week and not strong enough to fully crank it over.

Another thing, since it was sitting...your float in your carb could be stuck. You could spray some fuel into the air intake to see if it is a fuel starvation issue.

Share this post


Link to post
Share on other sites

Thx for all your help. I have changed batteries. I sprayed some starter fluid in the air intake. I was able to crank it for a few seconds but will not stay cranked. Also, will only crank if I spray the starter fluid. Would this suggest a fuel starvation issue? If so how do I need to trouble shoot? Thanks

Share this post


Link to post
Share on other sites


When you say "crank" are you saying that it sounds like it wants to start? If you're spraying starting fluid and it only sounds like it's going to start then...yes...it's not getting fuel.

Check your fuel petcock and make sure it's ok...there should be a lever or switch on the side of the quad or somewhere closer to the carb that has an ON, OFF, and RES setting. Make sure itis not on OFF..due to the fact that it was stored.

You may need to take the carb apart as it might have a stuckj float due to sitting around..happns. If the float is stuck down, fuel will not enter the carb bowl.

Share this post


Link to post
Share on other sites

drain the fuel and clean the carb they get gummed up with varnish from old gas. Plus stale gas has a much lower flash point and is not good for the wheeler.

Share this post


Link to post
Share on other sites
drain the fuel and clean the carb they get gummed up with varnish from old gas. Plus stale gas has a much lower flash point and is not good for the wheeler.

This sounds like it will fix it. I also run sea foam through every other tank of gas. It keeps everything clean.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Rick Robinson
      My Arctic Cat ATV started sputtering and backfiring and losing power on acceleration and sometimes die. It idles perfectly. I thought it may be the carburetor float sticking and would knock on the bowl and it would run great again for a while. It then started doing the same thing but I began hearing a loud knocking like low octane knock. This is intermittent and does not knock all the time. Thinking it was the carburetor float and possibly an obstruction in the jets I cleaned the tank and carburetor and put a new kit in. Still had the same problem. Bought a new OEM carburetor It still has the same problem at any adjustment? It also seems to improve a small amount when carburetor is disconnected from the filter system. I am starting to think it may be something else causing this possible a Coil or electrical? I would appreciate an experienced reply. I do have automotive shade tree experiences but this has me scratching my head. Thanks in advance!
    • By Adrian Ciotinga
      So I’ve had this quad for the better part of a month, and it’s been hard to start since the day I bought it. Once it warms up it idles just fine and has plenty of power and starts no problem, but cold it takes 20 seconds minimum of straight cranking to start it.
      It’s not really too big of an issue, I’m just curious as to why it takes so long. Earlier today, it took me about 2 minutes of on/off cranking to get it to fire.
      i have attached a video of a cold start to show you what I mean.
      FullSizeRender.mov
    • By Dwight Williams
      Hey everyone, I've been scratching my head over this for most of the day.  I bought a couple of Bayou 220's, got them running (they've both been sitting), and started tweaking and fixing small things.  One of them is mostly done, the other had an aftermarket carb on it and I've been trying to sort that out.
       
      Anyway, while adjusting the carb it died a few times, I restarted and moved on until it died and wouldn't restart.  I figured maybe I'd flooded it or something - after further attempts I realized I had no spark.  Since I have two identical machines I have many parts at my disposal.  I've swapped the CDI, spark plug and coil with no luck.  I have good resistance readings from the stator and pick up (135 and 110 respectively),  I don't have a peak voltage meter but I measure around 53VAC on the stator when cranking.  I have a 4 wire stator, not an alternator like the newer ones.  Grounds look good, I've checked the kill switch by verifying that it and the ignition switch grounds the black/yellow wire to the CDI.  I can turn the engine slowly and see the pickup short the meter as well, seems normal right?  So far everything I've checked looks the same on both machines.  I've got the service manual and wiring diagrams.  Do these readings make any sense?  I'm obviously missing something but I'm stumped.  thanks!
    • By Amazon Ads
      Where do you buy your ATV parts? Did you know that Amazon has ATV parts in stock for immediate delivery? You'll find all the best ATV parts and for great prices! Check out all the ATV parts available with free 2 day shipping now...
    • By Adrian Ciotinga
      Hello,
      I recently picked up an ‘07 KFX 700. All was going well, rode it about 40 miles, when it started bogging at low speeds. If I kept the revs higher, I was just fine. Also, a persistent issue since I picked it up is the fairly difficult start (but it is abnormally cold right now and the quad is jetted for the dunes at summertime).
      Regarding the complete lack of idle, I have to rev it a couple times to get it to idle after starting it, after which it’s 50/50 whether it remains idling. I don’t have low fuel, but all of this began after I rode it pretty hard and the radiator fan kicked in. Might be overheating, just wanted to hear your opinions.
  • Similar Tagged Content

    • By weblex
      Problem: The ATV starts and runs at idle perfectly. But as soon as I open the throttle, the engine starts to slow down until it stops. On the attached video you can hear the sound of how it works: see video below
      Prehistory: there is a Polaris Sportsman 500 1998, which for about 1.5 years stood in repair, including also replacing CDI with one taken from the same ATV. Finally, the vehicles were on wheels, traveled several kilometers and overheated - forgot to fill the antifreeze Came back home in small moves. The next trip started well, but after 10 km there was a feeling of a small drop in power (even as the vehicle got warm completely) but still drives. Next trip - the situation is repeated. The next test of ATV through time and a huge loss of power from the very beginning. The engine sneezes, does not want to go more than 5 mph.

      What has been done: the carburetor has been replaced with a new one (inexpensive, $ 40), a new spark plug, a new ignition coil, the engine head has been removed, the piston is in good condition, valves were corrected - but the problem was definitely not in them.

      Ignition control unit is suspected. Who faced similar? Please help in solving the problem.
      Thanks in advance.
       
       
    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
    • By chevyboy
      AL righty I did some trading around this weekend and ended up picking up a few 4 wheelers for cheap. I ended up with this one for $500 in it total and well the guy told me it dropped a valve. I haven't really messed with it at all. But this weekend I am going to try and start working on it some to get it running before winter time frame. So what I am asking is a couple of questions.
      1. First off where do I start I tried pulling the pull cord and could not get it to move at all.
      2. I need to get a service manual for this 4 wheeler where can I get it downloaded for free?
      3. what do I need to look for and how do I go about this really. I do have experience with 4 wheelers but this one is a little different to me than others because its a V2 and I have no clue where to start internal on the engines. Most of my experience is on the outside portion of troubleshooting on theses wheelers.
      Please no smart butt answers as i am new to here but just wanted opinions on where to start. Please and thanks wink:
    • By Wonderwoman
      Hello, well back to where I was last year with this carb. Took my 250 to the mountains for the first time this year and blue smoke, too much gas again. I can't believe that this carb gives me this much trouble. Seems like the choke is stuck but the cable moves freely. Anyone else ever experience this issue? Do you think a new choke cable would maybe resolve this?http://www.quadcrazy.com/atvforum/images/smilies/arghh.gif
      OK it was the choke. Put on all new cable and plunger and she is running 100% again. So now the question is, is the carb getting worn out where the plunger needle goes in the small hole and when I use the choke the needle end doesn't get lined back up with the hole?? We'll see how it runs and now that I know what the issue is I can always pull the choke plunger out and reinstall if I start having this issue again.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...