Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

January/February 2010 ATV Photo Contest


quadcrazy

Recommended Posts

  • 2 weeks later...

My Entry: 2008 Honda 450er Special Edition.170_0018.jpg

Frame: Stock, PC Candy Blue w. Teixeira Tech racing Gusset Kit

A Arms: ATV Four Play MGC +2.5

Swingarm: Stock

Steering Stem: Gibson/ Gibson Anti-vibe Clamp

Stbilizer: None

Axle: RPM Dominator II w. Race Hub

Carrier: RPm

Hubs F|R: Stock PC Candy Blue

Bars: Fasst Co. Flexx 14* Quad racer

Throttle/Clutch Lever: ASV Clutch Lever

Grips: Spider ATV Slim's

Nerfs: Rath Racing w/ Heal Guards

Bumper: IMS Classic

Front Shocks: LT Fox Racing Shox DSC

Rear Shock: Stock DeRisi Link

Rotors F|R: Driven/ Stock

Rims F|R: Stock/ Hiper Tech 3's

Tires F|R: Razr MX/ ITP MXR-6

Skid Plate: TAG Railer

Body:

Plastic: Black/ Quad Tech Hood

Graphics|Seat Cover: Stock/ Quad Tech Hump Seat

Number Backgrounds: Nac's

Handguards: Powermadd X Series

Bar Pad: Fasst Co.

Fuel Tank: Stock

Engine|Drive System:

Bore & Stroke: Stock

Displacement: 450

Cam: HRC

Carburetor: Stock FCR

Air Filter|Box: UNI/ HRC lid/Stock

Pipe|Silencer: Dasa Full Exhaust

Gearing F|R: 14/37

CDI|Killswitch: / Green wire mod/ Pro Design Killswitch

Cooling: Motul

Other: PC'ed Candy Blue: Brake Stay, Sprocket, Ft Brake Perch, Rear brake like holders. Free Flo* Vent tube.

Edited by Holeshotr15
Shortened To one Photo.
Link to comment
Share on other sites

My Entry: 2008 Honda 450er Special Edition, Pics at bottom.

Chassis | Suspension | Controls:

Frame: Stock, PC Candy Blue w. Teixeira Tech racing Gusset Kit

A Arms: ATV Four Play MGC +2.5

Swingarm: Stock

Steering Stem: Gibson/ Gibson Anti-vibe Clamp

Stbilizer: None

Axle: RPM Dominator II w. Race Hub

Carrier: RPM

Locknut: Stock

Hubs F|R: Stock PC Candy Blue

Bars: Fasst Co. Flexx 14* Quad racer

Throttle/Clutch Lever: ASV Clutch Lever

Grips: Spider ATV Slim's

Nerfs: Rath Racing w/ Heal Guards

Bumper: IMS Classic

Grab Bar: Stock

Front Shocks: LT Fox Racing Shox DSC

Rear Shock: Stock DeRisi Link

Brake Lines: Stock

Rotors F|R: Driven/ Stock

Rims F|R: Stock/ Hiper Tech 3's

Tires F|R: Razr MX/ ITP MXR-6

Skid Plate: TAG Railer

Body:

Plastic: Black/ Quad Tech Hood

Graphics|Seat Cover: Stock/ Quad Tech Hump Seat

Number Backgrounds: Nac's

Handguards: Powermadd X Series

Bar Pad: Fasst Co.

Fuel Tank: Stock

Engine|Drive System:

Bore & Stroke: Stock

Displacement: 450

Cam: HRC

Carburetor: Stock FCR

Air Filter|Box: UNI/ HRC lid/Stock

Pipe|Silencer: Dasa Full Exhaust

Gearing F|R: 14/37

CDI|Killswitch: / Green wire mod/ Pro Design Killswitch

Cooling: Motul

Other: PC'ed Candy Blue: Brake Stay, Sprocket, Ft Brake Perch, Rear brake like holders. Free Flo* Vent tube.

170_0028.jpg

170_0034.jpg

170_0030.jpg

170_0027.jpg

170_0025.jpg

170_0019.jpg

170_0033.jpg

All your text will be gone at voting time and only the first pic will be used. Great looking quad

Link to comment
Share on other sites

That is just how QC does it. They just take the first picture. I don't recall seeing any text in previous contest.

I think that we should make an exception to that, like I said I think it is important for voters to know what has been modified. The theme is described as" "Best Modified From Original" is basically anything that makes your machine different from factory (OEM) original. This could be addons, mechanical modifications, graphics, exterior accessories (luggage, winches, grips, ...), tires, etc..." I think that alot of the details listed in the contest description might not be noticed or explained well enough by a single pic. For example, if I were to enter my TRX 500R, and the only thing you had to go on was this pic, then most people would not see all of the time, custom fab work and enginuity that has gone into this project. At first glance, it looks like a relatively normal '86 250R with poorly painted plastics. What you may not notice is that the frame is completely hand made from a jig built off of an actual 250R frame, or the extensive modification necessary to stuff a CR 500 motor into it and make all of the intake plumbing squeeze by the rear shock, or that the pipe was actually hand made by some one to fit the 250R frame, but is tuned for a CR 500 motor. You may not notice the +2 400ex a-arms that have been modified to work properly with the KFX 450 shocks, or the custom shock mounts that had to be made from scratch to fit them on the machine. You may not notice the modified kick starter that had to be extended out from the motor in order to clear the rear brake master cylinder, or the brace and custom machined brass bushing that keep the side cover from cracking due to the extra pressure put on it by the kicker sticking out so far from the motor. You cant see inside to see the '87 crank that has a rod that is 5mm longer than the stock '86 crank, and it would be hard to notice the spacer plate machined for me by Cometic gasket co. to compensate for the longer rod. You definately would not notice the hand fabricated adaptors that allow for the use of the twin piston 250R brake calipers on the ex spindles because the ex brakes do not cut the mustard on this machine. You would not be able to tell that the entire rear suspension is actually off of an '85 ATC 250R with the exception of the shock which is one of the only actual factory '86 TRX 250R parts on this machine aside from the front brake calipers plastics, thumb throttle and brake lever/resivior.

DSC00621-1.jpg

Edited by DirtDemon
Link to comment
Share on other sites

All your text will be gone at voting time and only the first pic will be used. Great looking quad

We start a separate thread always for voting, this thread remains.

Why will all the text be deleted? I would think that a description of the machine is somewhat important. Voters should know how much work has gone into each project.

It's a photo contest, so we start a separate thread with all the photos in a row. This thread can always be referenced. Your text will remain.

That is just how QC does it. They just take the first picture. I don't recall seeing any text in previous contest.

Yes, first photo added will be used in the contest.

Link to comment
Share on other sites

  • 2 weeks later...

1994 POLARIS 400L 4X4

polaris.jpg

quad stripped down to bear bones. and built back up again

new suspension

2500lb gorilla winch

engine rebuilt and polished

transmission polished cleaned

new front and real DIRT DEVIL TIRES 25x8x13 in the front 25x12x12 in the back

Plastic custom painted FLAT BLACK

Racks and front bumper as well as a few other pieces painted Gloss Red

Everything else was replaced with new OEM parts

Link to comment
Share on other sites

This is our 2005 blaster far from stock and 2008, 2009 Series Supercross Champion.

7329_154758406962_711666962_3486973_2591709_n.jpg

2005 blaster 200cc motor Factory 7 Fire-Breather 200cc Cylinder Kit-, Milled head, Project blaster green race plastic Project blaster vented hood, DG National Series Front Bumper: DG National Grab Bar, Moose Billet Thumb Throttle , Gibson Stearing dampner ,DuraBlue Eliminator Axle, ROLL DESIGN ATV Steering Stem, Fasst Flex Bars with anti vib dampners, 30mm Kiehn carb, reed spacer, v-force 3 reeds, American Star Long Shock A-Arms, 4 Douglas beadlock rims , 2 Razor rear tires,2 Front ITP Holeshot MXR Tires 19x6x10, Gas cap carbon fiber, Extreme Manufacturing Pro Peg Nerf Bars, Project Blaster Factory Aluminum Airbox, American Star new +4 roundhouse swing arm, rear Elka long travel duale rate rezi shock, front Triple Rate elka shocks/remote rezzi dual adj, notrology hot wire coil, lightend flywheel, barrenet clutch kevlar, after market inner and outer HD clutch basket, AMP RESEARCH LINK

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Tuzz
      Bucking started about a month ago and works ok after 1/2 hour warmup.  Today while working on it i discovered that if i put the ignition switch in LIGHT position it runs fine right from the start.
      I'm stumped!  Any idea why this could be?  

    • By huntindog
      I am in the process of puting it back together after replacing the DPS gearbox.
      The manual I have states that it will need to be flashed by a dealer. Is this still true?
      Also , I have a mystery bolt That I cannot remember where it goes. M6x 70 or so.  Hex head with a flat washer.I will try to attach a pic.
      Pic is no go for now....Cox issue I will try again later
      TIA
    • By 2wdrancher
      Hello everyone I have done a ton of research on doing this conversion because I hate getting stuck in the stupidest places and not being able to back out. I will be documenting my conversion here and on a couple other forums and probably post a couple videos on YouTube. So what I’ve come up with is all you need is a front axles, front propeller shaft, the final shaft inside the engine and the 4x4 front engine cover . I will list all the part numbers for everything that you need and prices from about six months ago (sorry) , you DONT need to switch out hubs, knuckles, or anything like that, and if you want differential lock lock like the foreman and Rubicon you can get a foreman Rubicon front differential and propeller shaft with the diff-lock and get a knight sure four manual actuator for it and voilà you have four-wheel-drive rancher. Input from you guys is greatly appreciated thank you for your time!
      Note: I would definitely get the aftermarket HD axles because they are definitely stronger and are around the same price as oem 
      FINAL SHAFT
      23611-HR3-A40  =$80.48
       
      BEARING
      91006-HP5-601   =$11.11
       
      OIL SEAL
      91202-HR0-F01   =$ 7.94
       
      COVER ASSY., FR. CRANKCASE
      11300-HR3-WB0   =$206.99
       
      PROPELLER SH AFT
      40400-HR3-A20   =$91.50
       
      FINAL GEAR
      41400-HR3-W50   =$714.88
       
      FINAL CASE BRA CKET
      50350-HR3-A20  =$7.40
       
      FLANGE BOLT
      95701-08016-08  =$1.49
       
      R. SHAFT SET
      44250-HR3-WB1  =$240.64
       
      L. DRIVESHAFT
      44350-HR3-WB1  =$240.64
      This is all for the 2x4 - 4x4  lever that comes in stock on the ranchers. I would definitely recommend looking for parts for wheelers on marketplace,  or craigslist
       
      001
      NUT, ADJUSTING 
      41560-HP5-600
      $6.51
       
      002
      CABLE, FR. FINAL CLUTCH 
      41570-HR3-A21
      $6.56
       
      003
      SPRING, CLUTCH CABLE 
      41571-HP5-600
      $1.95
       
      004
      CLIP, CLUTCH CABLE 
      41573-HP5-600
      $3.23
       
      005
      GROMMET, CLUTCH CABLE 
      41716-HP5-600
      $3.12
       
      006
      LEVER, FR. FINAL CLUTCH 
      54030-HP5-600
      $8.91
       
      007
      PILLOW BALL, FR. FINAL CLUTCH 
      54031-HP5-601
      $10.87
       
      008
      BRACKET, FR. FINAL CLUTCH 
      54040-HP5-601 
      $11.19
       
      009
      SPRING, FR. FINAL CLUTCH 
      54041-HP5-600
      $1.86
       
      010
      GATE, FR. FINAL CLUTCH 
      54050-HR3-A20
      $4.55
       
      011
      GRIP, FR. FINAL CLUTCH 
      54321-HP5-600
      $8.95
       
      X2 012
      BOLT, FLANGE (6MM) 
      90111-162-000
       
      $2.54 
       
      013
      NUT, SELF-LOCK (6MM) 
      90343-ZE6-000
      $1.70
       
      014
      JOINT B, BRAKE ARM 
      95015-32001
      $0.82
       
      X3 015
      BOLT, FLANGE (6X12) 
      95701-06012-00
      $1.34
       
       
      Or Forman 520 w diff lock
       
      FINAL GEAR
      41400-HR4-A21  =$732.49
       
      PROPELLER SHAFT
      40400-HR4-A20  = $92.54
      And you definitely need the sure four locker for this
    • By vlxerdon
      Hello from southeast Georgia. Was gifted a 2000 Yamaha bear tracker with out a carb or battery and looking like it had seen better days. Was told it had sat for about three years. Explained a lot. Put a carb on and a battery in and it started right up. Surprised the heck out of me  Anyhow as stated in my opening I am  78 years old with a very long motorcycle backgground but brand new to atv's. Anyone else out here from Georgia? Would like to meet up with some folks for a ride or two. Looks like a great site. Thanks for having me. 
      Don
    • By p5200
      I've been using Valvolene 10w 40 ATV oil but, it's like $8.00 a quart. Is that about the going rate? Or is there cheaper alternatives that would be suitable? Thanks
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.



×
×
  • Create New...