Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

boxloc

1996 Suzuki King Quad 300 4x

Recommended Posts



Don't know much about that machine specifically, but I do know that the better you take care of it, the better it will be to you. Hopefully the person you bought it from knew that too. I also highly advise that you have fun with it.

Share this post


Link to post
Share on other sites

it is a loverly bike with a good history.

most people love the inderpendnt rear suspention, even if it looks a bit strange! it works well.

often they get a problem with the fuel tap being broken that lets fuel pass through the vacume line and it floods the motor, but is easy to fix.

often the carbi can get worn on the older bikes with high mileage (worn in the needel and needle jet) and it makes the bike run rich. once again easy to fix.

and then there is the issue with the carbi getting contaminated with rust dust and dirt which makes its way in to the carbi (but it happens to every bike)

some times the slave cyliners in the front brakes get old and rusty and make the brakes get stuck on a little bit, but it is only a every 5 years or so thing to have happen.

but it is a good all round bike that suzuki shops (like where I work) sadly miss! and wish it would come back in production, we still have farmers asking for them, even tho is it 6 years after production stopped!

Share this post


Link to post
Share on other sites

Thanks "Mate"........I bought it for riding in Michigan's Upper Peninsular and to plow my driveway in Chicago....that LOW LOW gear is really LOW......I'm having a minor stall problem.... feels like it idles too low.....but expect to fix it when my repair manual arrives this week....again thanks for the good info.....

boxloc..............

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By JacobSlabach
      I have a gentleman that asked me to service his bayou for him.  I have always wondered what oil should be used in atv engines?  Pros?  Cons?  What weight should be used in what type of weather?  Is there one kind that I could bulk buy and safely used in any quad I worked on or owned?  What about performance?  Engine Life?  This has always been a 🤔🤔🤔 area for me with quads as far as why you would use one type of oil over another....
      Thanks!
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By Meg Sam
      Hi I have bought a Bashan bs200s-3 and I am wondering where I can buy parts for this as I need a full new wireing loom also does this model have reverse gear?
  • Similar Tagged Content

    • By Chris Chitwood
      Hi, I’m a 16 year old that is wanting to get more into vehicle and mechanic repair. My dad has an old ‘96 Timberwolf that he doesn’t remember running since I was born. I want to get it running again as a memory for him and to help us be able to hunt together, and of course so I can learn how engines work more than the little information I know now. I’ve pulled the carburetor and gas tank off of it, and the carburetor is getting cleaned by a friend. I can post photos of the condition it’s in later, I’m just curious where I should start in my journey to get it running again. The power switch is broken off of the handlebar, so I am looking into fixing it, along with the pull cord. I’m afraid the engine is seized up, and I’m curious to hear any input anyone has. Thank you all.
    • By Craig Butterworth
      Hi, i'm looking for some help and advice with my arctic cat quad, its the first of the arctic cat quads as far as i know, manufactured in 1996 the bearcat 454. i have owned the quad for about 10 years now but just recently it has developed a problem with reverse gear, reverse wont engage any more like it used to 😕 the cable and handle is free but there is no movement the gearbox end, can anyone give me a heads up of what is involved to fix this? 🤔
      If anyone has a service/repair manual available for it as well that would be greatly appreciated! 🙂
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By skgw1
      Feul pump went out. Replaced. At times quad cuts out like its not getting gas. Saw article on new pump needs to be calibrated. Told how to go into a service mode. Does not tell how to calibrate after going into mode. Can anyone shed light on this procedure.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...