Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Smoothbassman

Repairing a Synthetic Winch Line - Walkthru

Recommended Posts

There are tons of advantages to switching to synthetic winch lines on your ATVs. Lighter weight, safer pulls, and best of all, instant repairs if you have a failure of your line while doing a pull. If you are caught with a broken line during a pull you can splice it back together in no time and be winching in 15 minutes or less and heres how.

All you need is a few simple tools and a couple sets of instructions in your toolkit.

Tools:

Sharp Scissors, or Blade

Electrical Tape

Sharpie Marker

Tubular Rope Fid about 1/2 the diameter of your rope line and at least 4-6 inches long

DSC01802.jpg

Formal Instructions:

Eye Splice

End Splice

First you need to measure out the length of your repair. I like to use 2 times the length of the tool that you are using to tread your taper tail down the center of the rope. Make a mark at one length, and a second mark at the second length. The second mark will be where you stick the tail thru your line at.

DSC01804.jpg

Now just past the 1st mark you made mark 3 pairs of rope to cut to make your tapered tail.

DSC01808.jpg

Pull those threads out of the line and cut them off.

DSC01810.jpg

Your tail should now look like this

DSC01811.jpg

The end of your rope should now have only six strands, instead of twelve. Take the end of your rope with 6 strands, and slip your fid thru the center of the rope and tape it to your fid.

DSC01813.jpg

DSC01814.jpg

Thread your taped fid thru your hook and back into the center of the rope, at your 2nd mark.

DSC01817.jpg

DSC01816.jpg

You now have a very large loop in the end of your rope. Push the end of the rope up through the middle of the rope. You'll need to kind of "bunch up" the rope to loosen it up enough to push the other rope through the middle.

DSC01819.jpg

As you bury more and more or the end of the rope, the loop will get smaller and smaller. Eventually you will have the loop very tight around the hook. Pull the end of the rope out so you can pull it nice and tight around the hook. Remove whatever object you taped to the end of the rope to guide it through, and pull the rope tight to re-bury the end. You may have to cut a little off the very end of the rope to get it all to re-bury itself. You have a completed eye splice.

DSC01821.jpg

DSC01824.jpg

DSC01822.jpg

After getting it tight around your hook, pull down and away from the hook on the outer wrap to lock the splice in place.

The end splice is exactly the same except that you now have to create two tapered tails and bury each tail into the two sections of winch line to create the splice. Just in case you break your line in the middle of a pull.

With a little patience you can repair any line in minutes.

Share this post


Link to post
Share on other sites


I you need synth rope in a hurry you can go to any marine store like WestMarine. I have my ropes made up by them from 3/8" x 65" to 1"x75'. I use them for repairing Verizon winch lines. Steel winch lines are not allowed by law due to electrocution hazards. When ordering winch line make sure you get "stablebraid"

It wont stretch easy and doesnt try to rotate when being pulled

Edited by marioweldinginc

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ellery Zandt
      Does anyone have a redcat 250 or falcon 250cc that they can share where the two vacuum lines on the carburetor that you run antifreeze through I honestly have no idea where the lines are suppose to go to circulate the antifreeze. 
       
      Any help is greatly appreciated. 
       
    • By Gilbey
      Just got 2018 Suzuki King 400 ASI, getting ready to install winch on it. Noticed the wire loom up front on top of frame to pass wires through but not quite sure where the loom comes out at. I am assuming by the battery but it is not visible........would you guys just wire direct to battery as I had on previous quad or is there a better spot to wire to? I had noticed a wire junction on top of driver rear wheel with nothing connected to it and was curious if my leads could bee run to that? May have to go to dealer to see if a mechanic there can give me some insight to this process. Thoughts and ideas greatly appreciated.
    • By Admin
      Yamaha Australia has announced it will discontinue selling Utility ATVs due to new Australian government legislation that requires the mandatory fitment of so-called Operator Protective Devices (OPDs), YMA will not sell utility ATVs after the government compliance deadline of 11 October 2021.
      “The decision to make the fitment of OPDs compulsory is disappointing. The ruling has forced us to withdraw utility ATVs from the Australian market because as a manufacturer we are not willing to gamble with our customers lives by bolting untested devices onto our specifically engineered and designed ATVs,” explains YMA Director Brad Ryan.
      As the market leader in this segment, Yamaha recognises that utility ATVs are an important part of farm operations and will comply with stage one of the new consumer legislation. This includes testing and the fitment of warning labels by Oct 2020. This will ensure that Yamaha ATVs remain available until October 2021.
      After this date customers will not be able to purchase a new Yamaha utility ATV in Australia – but sport and youth models will continue to be available. This is because new sport and fun ATVs do not need to be fitted with OPDs. In addition, side-by-side vehicles (SSVs) are not affected by this ruling, so YMA will support our utility ATV dealers and ease the transition from ATV to AG bike and SSV business.
      “Fortunately, our utility ATV customers can transition to our equally capable lineup of AG bikes and expanding SSV range,” adds YMA Director Brad Ryan.
      Customer safety has always been our priority. YMA has provided market leading rider training and promoted proven safety methods. YMA also helped develop the Shark ATV helmet which is the only fully certified farm safe ATV helmet available. YMA feels so strongly about customer safety that purchasers of new Yamaha utility vehicles will receive a free Shark farm safe helmet valued at $250 while stocks last.
      YMA is also fully committed to customer care via a national dealer network that will continue to service ATVs and with the supply of parts and accessories into the future.
      Source: https://www.dirtaction.com.au/yma-to-discontinue-utility-atvs/
    • By MarkinAR
      And the new 300FW is already wounded. Something got in a bind and blew the whole chunk of case out around the primary drive gear at the back of the motor. In the pic you can see the crack along the top...there is a big chunk missing from the bottom. And it won't roll....but the front and rear diffs both seem fine. Unfortunate. This looks to be a bit of a project. Still feels like it will shift through gears so i'm wondering if the ring and pinion just jumped a bit and blew something to pieces.  I have a parts bike.  But will this require the case to be split and transmission completely disassembled?  I assume you can't just slide the broken primary drive out and slide the replacement in?
       

  • Similar Tagged Content

    • By ATVNetwork
      It´s one debate that doesn´t seem to be going anywhere fast. If you´re buying a brand new winch like the Superwinch Terra 45 or maybe it is just time to replace your old cable. Which way do you go: steel or synthetic? Let´s take a look at the pros and cons so you can decide once and for all which is better for YOU.
       
      Life of the Cable
      After an extended period of time depending on use, a steel cable can start to crimp, get rust spots or develop frayed strands of steel cable which can give you nasty cuts and also decrease the reliability of the cable. In the short term, the steel cable can take a lot more abuse than the synthetic variety. However, synthetic cables can have a much longer life. That is of course only if it is taken care of and carefully prevented from fraying on the edges. Fraying edges on a synthetic cable is the beginning of the end for this more costly type of cable. The more affordable steel cables might be more attractive for the rugged wincher who doesn't mind replacing a steel cable at the first signs of wear.

      Potential and Kinetic Energy
      You don´t need to be a science major to recognize the danger of a cable under extreme tension. Whether it is due to overbearing the cable or a replacement cable is well overdue, it can be a potentially very dangerous situation. In terms of this, Synthetic is generally the winner as it doesn´t become a dangerous projectile. It is also easier on the hands and actually provides more pull per inch. Bear in mind however, that your maximum pulling power is still limited by the winch you select. It´s downside is that if it is in contact with a sharp edge, it has the possibility of slicing or fraying the edges, which is very unlikely with a steel cable.

      UltraViolet
      Some users of synthetic cable have made complaints about UV damage causing weakness that leads to a decrease in strength. Newer synthetic lines are being manufactured UV resistant, and a winch cover is also a cheap solution to this problem.
       
      Company Choice
      About 95% of new winches are being shipped by their companies with standard steel winch cables. This can be taken as just because they are the cheaper option of the two for them to make the most profit, or a signal that it is still the best choice of cable.

      Power
      As I mentioned before, Synthetic does provide you with more pounds per inch. Which means more pulling power for less cable. Even though pulling power is generally determined by the winch, check out this article with tips for both types of cables on how to double your pulling power.

      Conclusion:
      Synthetic is the latest and more expensive cousin, that still has a few kinks to iron out before it really replaces steel cables completely. Steel has been proven in every condition. It is tried and tested and cheaper. For reliability and cost, definitely your cable of choice.

      Author:
      Sam is an ATV enthusiast and updates his adventure website with outdoor tips and articles, including a review on the Superwinch Terra 45 (1145220)
    • By Racer944
      Hi Folks;
      Has anybody on here installed a winch on a 2003 Magnum 2x4? I am using a Cycle Country adapter plate (only one I could find), but am having a bit of trouble getting it all to fit properly, and am looking for someone that may have done this install and/or may have some pics of the installation.
      Thanks!
      Eric
    • By toonces
      My mother has just developed a fairly serious case of sciatica, which is a condition where you have some serious leg pain as the result of a pinched sciatic nerve. One of the exercises she does in physical therapy is simply the therapist holding onto her foot and pulling away from her hips as she lays on her back on a table. To replicate this exercise at home they have recommended an inversion table (where you turn upside down and hang from your feet), but since she's not too keen on this idea I'm trying to figure out how to replicate this exercise...which is where the idea of a remotely operated winch comes in.
      I don't really have a wide range of knowledge when it comes to what equipment is out there that can help me accomplish this goal, but I'm not too shabby at designing things and since I just installed a superwinch on my grizz this is the first idea I've come up with.
      Basically I'm imagining using some kind of winch whose rope would be worked through a pulley system that would end attached to a shoe which Mom would put on, lie down and use the remote switch to gently stretch the leg.
      - Winch (if an ATV winch) would be powered by a 12v car battery hooked up to a trickle charger
      - Safety mechanisms would include...
      - a light switch dimmer inline between the 12v battery and the winch so speed can be adjusted.
      - possibly using one of those stretchy rubber exercise resistance bands in the line segment to regulate and ease the pulling
      - a remote power cut off switch paired with the remote 'in/out' switch
      Honestly I could just go ahead and make this system myself, and I'm fairly sure it would work, but I thought I'd bounce this idea off a mechanically minded community to see if there are any ideas how I could improve on the design.
      Since I'm only familiar with ATV winches at this point that's what I've imagined using. But if anyone is aware of a 110v based winch that would be more appropriate, that would surely help in simplifying powering the system since it'll be located indoors. Only requirement for the winch would be that it would need both an in and out function operated by a remote switch. And since the winch would only need to pull between 10-20 lbs it wouldn't need to be nearly as beefy as the ATV type.
      Sorry for the long write up here but I'm certainly glad for your time and open to your opinions and suggestions.
    • By dwint
      my speedometer stopped working on my 91 kq and took the plastic off but how do I replace it when its under the tank and you cant get the tank out unless you remove the engine
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...