Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
By M C
A friend of mine has this particular 4 wheeler. It sat in the garage for about a year, so I redid the carb, cleaned the tank and installed a new petcock. So far, it cranks right away whether its button started or pull started. So I have a couple of questions concerning the carb and air filter.
1. Is this a cvk32 250 or 350 carb? As the air fuel ratio adjustment is different according to a cvk document I read. What's your adjustment setting? 2 whole turns and a 1/8 or 2 whole turns and a 1/2? Comparing the old setting on the carb to the new setting (and where the needle sits now), makes me think it was way off before.
2. The Air filter cover, gasket, air filter and plate element are all missing. So I was thinking of removing the hose that goes to the air box and put one of those K&N style looking filters and be done with it. So my question is.. will I have to readjust Air Fuel screw or just adjust Idle?
It's just going to be driven around the neighborhood.
Thanks in advance for any info or help. Y'all stay safe out there!
By Ted Craig
I know a lot of people say not to use anything but Oem. For the sake of the those who chose not to, or the OEM part cost more than the project, lets hold back negative comments.
I just purchased a carburetor that is supposed to be up to OEM specs. The company has a good reputation on eBay and Amazon. The Carb is supposed to be for this bike and jetted exactly.
This question should basically go under carb adjustment. I installed the new carb, the bike idles fine. On throttle it sputters half the time and the other half it will rev up fine. Does this sound like the needle is set at the wrong point? Does it sound like the main jet is the wrong size? Or is there another adjustment besides the air/fuel screw thats is 2 turns out?
Yes i could truck through old threads and possibly find the answer, but i thought it would be nice to have one tailored to new carb installs.
Similar Tagged Content
By Anthony Marceau
Hi everyone! I have a 1986 yamaha moto4 200 that's been sitting for a while! Cleaned the carb, replaced engine oil, put fresh gas in it. Got it running and went for a ride! It was running great just a little backfire once in a while! I barely made it home on the way back and now the bike won't run at all since then! It will start if I give a little bit of throttle but dies instantly as soon as I let go off the throttle! And even if I try to rev it up it'll sound like its not getting enough gas.. it revs up a couple hundred rpm's and backfires through the carb.. it almost sounds as if I was trying to take off from zero in 5th gear! Nothing is seized though! I dissasembled the head and the piston and cylinder are fine! Rebuilt the carb, replaced the ignition source coil.. I don't know what to do anymore.. compression test shows 90 psi Specs are 128 psi but i'm not sure if I trust my compression tester.. any ideas? Thanks!!
This is my first post and I was wondering if there is anyone who can help me solve a problem I have with my Yamaha Kodiak 400 4x4 Fitted with a Mikuni Carburetor . The year of the quad is around 1998, the reason I am not sure of the date is, there wasn't any paperwork and no details on the frame either.
The quad had a bad leak from the carb overflow which indicated that the float needle valve was blocked or passing so I replaced this and put everything back together. The quad ran really well until I took it onto some rough ground to have a ride around, a few hours later the engine started to run really rough as if the engine was flooding. I have removed the carb again and cleaned the needle valve out and the whole of the carb just in case there where any dirt behind it. Engine now runs fine again but fuel has started to run out the carb overflow again.
I have tried everything to try and stop the fuel leaking out the overflow but its still happening. My last thoughts where to adjust the float level and its still happening.
Has anyone got any thoughts on the problem or could suggest whats causing the fuel leaking out the overflow.
Thanks for reading
Recently Browsing 0 members
No registered users viewing this page.